What are the setbacks for a duplex in NSW?
Written by Shea Cullen, architect, for Dudils.
A setback is how far a home must sit from each boundary of its lot. For a duplex in NSW they come from one of two places: the state's complying development codes, or the council's development control plan (DCP) when you lodge a development application.
This page gives the state figures and every council's main figures, and links each council's own page.
NSW addresses only. Free, and no sign up.
How close to the boundary can a duplex be in NSW?
As complying development, a duplex on a 600m² (15m wide, 40m deep) lot can sit 0.9m (1.5m at two storeys) from the side boundaries and 3m (8m at two storeys) from the rear, with a 4.5m front setback. Those are the figures the Site Checker reads from the state codes; the table gives them for three example lots, 450m² (15m wide, 30m deep), 600m² (15m wide, 40m deep) and 1,000m² (20m wide, 50m deep).
Under a development application the council's DCP sets them instead, and the councils differ. Of the 111 councils whose main plan sets a side setback for a duplex, 46 ask for 0.9m, the most common single figure. Of the 110 councils whose main plan sets a rear setback for a duplex, 19 ask for 3m, the most common single figure.
| Example lot | Front | Side | Rear | Corner block, second street |
|---|---|---|---|---|
| 450m² (15m wide, 30m deep) | 4.5m | 0.9m (1.5m at two storeys) | 3m (8m at two storeys) | 2m |
| 600m² (15m wide, 40m deep) | 4.5m | 0.9m (1.5m at two storeys) | 3m (8m at two storeys) | 2m |
| 1,000m² (20m wide, 50m deep) | 6.5m | 0.9m (1.5m at two storeys) | 5m (12m at two storeys) | 3m |
Are duplex setbacks different from a house?
Sometimes. Under complying development a duplex follows the Low Rise Housing Diversity Code rather than the Housing Code, as the Site Checker reads them. On the 450m² lot and the 600m² lot the two codes give the same figures. On 1,000m² (20m wide, 50m deep) it reads front 6.5m, side 0.9m (1.5m at two storeys), rear 5m (12m at two storeys) for a duplex, against front 6.5m, side 1.5m (2.1m at two storeys), rear 5m (12m at two storeys) for a house.
Under a development application, 85 of the 128 councils' main plans ask the same single storey front, side and rear of a duplex as of a house.
Is a dual occupancy the same as a duplex?
Yes. Dual occupancy is the planning term for two homes on one lot, joined or separate, and most people call it a duplex. Council plans and the state code use dual occupancy, so search your council's DCP for that term.
Does a two storey duplex need bigger setbacks?
Under complying development, yes: on a 600m² (15m wide, 40m deep) lot the front setback is 4.5m, the side 0.9m (1.5m at two storeys) and the rear 3m (8m at two storeys). Under a development application it depends on the council: 77 of the 128 councils' main plans set a different front, side or rear figure for two storeys, and each council's page shows both.
Do council rules or complying development apply to my duplex?
It depends on how you get approval. With a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, the state codes set the setbacks and the council's plan does not apply. With a development application, the council's development control plan (DCP), the council's own rules for the design of homes in its area, sets them. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.
6 of the 128 councils' main plans set no front, side or rear setback for a duplex; there, ask the council what it expects.
What does each council ask for a duplex?
The table gives each council's main plan at one storey; follow a council for its two storey figures, its clauses and its other plans. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot.
| Council | Front | Side | Rear |
|---|---|---|---|
| Albury City | the average of the neighbouring homes (4m where there are none) | 0.9m | 2m |
| Armidale Regional | 4.5m | 0.9m | 0.9m |
| Ballina | at least 4.5m, or the street's established building line where that is further back | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) |
| Balranald | 6m | not set by the council's policy: ask the council | not set by the council's policy: ask the council |
| Bathurst Regional | at least 6m, or the street's established building line where that is further back | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Bayside | the average of the neighbouring homes (6m where there are none) | 0.9m | 5m |
| Bega Valley | no figure on lots up to 349.99m², the average of the neighbouring homes (4.5m where there are none) on lots up to 550m², the average of the neighbouring homes (5m where there are none) on lots up to 900m², the average of the neighbouring homes (6m where there are none) on larger lots | 0.9m | no figure on lots up to 349.99m², 4m on lots up to 900m², 5m on larger lots |
| Bellingen | at least 4.5m, or the street's established building line where that is further back | inside a plane rising at 35° from 3m above the boundary, and at least 0.9m | inside a plane rising at 35° from 3m above the boundary |
| Berrigan | the average of the neighbouring homes (4.5m where there are none) | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Blacktown | 6m | 0.9m | 0.9m |
| Bland | 5m | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Blayney | at least 4.5m, or the street's established building line where that is further back | 1.5m | 1.5m |
| Blue Mountains | the average of the neighbouring homes (8m where there are none) | 1m | 4m |
| Bogan | 6m | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Bourke | 4.5m | 1m | 1m |
| Brewarrina | 6m | 1m | 1m |
| Broken Hill | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Burwood | the average of the neighbouring homes | 0.9m | 3m |
| Byron | 4.5m | inside a plane rising at 45° from 1.8m above the boundary, and at least 1.5m | inside a plane rising at 45° from 1.8m above the boundary, and at least 1.5m |
| Cabonne | 8m | not set by the council's policy: ask the council | not set by the council's policy: ask the council |
| Camden | the average of the neighbouring homes (4.5m on lots up to 900m²; 6.5m on lots up to 1,500m²; 10m on larger lots where there are none) | 0.9m | 4m |
| Campbelltown | 5.5m | 0.9m | 3m |
| Canada Bay | at least 4.5m, or the street's established building line where that is further back | 0.9m | 6m |
| Canterbury-Bankstown | 5.5m | 0.9m | not set by the DCP: ask the council |
| Carrathool | 6m | not set by the council's policy: ask the council | not set by the council's policy: ask the council |
| Central Coast | the average of the neighbouring homes (4.5m where there are none) | 0.9m, plus 0.25m for every metre of wall above 4.5m | 4.5m |
| Central Darling | 4.5m | 1.5m | 4.5m |
| Cessnock | 6m | 1m, plus 0.3m for every metre of wall above 3m | 1m, plus 0.3m for every metre of wall above 3m |
| Parramatta | at least 6m, or the street's established building line where that is further back | 1.5m | 30% of the lot depth, and at least 10m |
| Clarence Valley | at least 6m, or the street's established building line where that is further back | 0.9m | 0.9m |
| Cobar | not set (the council has no DCP): ask the council | not set (the council has no DCP): ask the council | not set (the council has no DCP): ask the council |
| Coffs Harbour | 4.5m | 0.9m | 3m |
| Coolamon | 8m | 0.9m | 3m |
| Coonamble | 7.5m | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Cootamundra-Gundagai Regional | the average of the neighbouring homes (4.5m on lots up to 599.99m²; 4.5m on lots up to 899.99m²; 6.5m on lots up to 1,499.99m²; 10m on larger lots where there are none) | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Cowra | the average of the neighbouring homes (6m where there are none) | 0.9m | 3m |
| Cumberland | the average of the neighbouring homes (4.5m on lots up to 900m²; 6.5m on lots up to 1,500m²; 10m on larger lots where there are none) | 0.9m, plus 0.25m for every metre of wall above 4.5m on lots up to 24m wide; 1.5m, plus 0.25m for every metre of wall above 4.5m on lots up to 36m wide; 2.5m on wider lots | 3m on lots up to 900m²; 5m on lots up to 1,500m²; 10m on larger lots |
| Dubbo Regional | the average of the neighbouring homes (4.5m where there are none) | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Dungog | 6m | inside a plane rising at 45° from 1.8m above the boundary, and at least 0.9m | inside a plane rising at 45° from 1.8m above the boundary, and at least 0.9m |
| Edward River | the average of the neighbouring homes (5m where there are none) | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Eurobodalla | the average of the neighbouring homes (5.5m where there are none) on lots up to 2,499.99m²; 7m on lots up to 4,999.99m²; the average of the neighbouring homes (5.5m where there are none) on larger lots | 0.9m on lots up to 2,499.99m²; 5m on lots up to 4,999.99m²; 0.9m on larger lots | 3m on lots up to 2,499.99m²; 5m on lots up to 4,999.99m²; 3m on larger lots |
| Fairfield | the average of the neighbouring homes (6m where there are none) | 0.9m | 0.9m |
| Federation | the average of the neighbouring homes (4.5m where there are none) | 2m | 2m |
| Forbes | the average of the neighbouring homes (6m where there are none) on lots up to 50m deep, the average of the neighbouring homes (8m where there are none) on lots up to 70m deep, the average of the neighbouring homes (10m where there are none) on deeper lots | 0.9m | 0.9m |
| Georges River | at least 4.5m, or the street's established building line where that is further back | 1.2m | 15% of the lot depth, and at least 6m |
| Gilgandra | at least 7.5m, or the street's established building line where that is further back | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Glen Innes Severn | the average of the neighbouring homes (6m where there are none) | 0.9m | 0.9m |
| Goulburn Mulwaree | 4.5m | 1m | 6m |
| Greater Hume Shire | the average of the neighbouring homes (4.5m where there are none) | 2m | 2m |
| Griffith | 6m | 0.9m | 2m |
| Gunnedah | the average of the neighbouring homes (6.5m where there are none) | 0.9m | 0.9m |
| Gwydir | not set (the council has no DCP): ask the council | not set (the council has no DCP): ask the council | not set (the council has no DCP): ask the council |
| Hawkesbury | the average of the neighbouring homes (7.5m where there are none) | inside a plane rising at 45° from 1.8m above the boundary | inside a plane rising at 45° from 1.8m above the boundary |
| Hay | 5m | 0.9m | 0.9m |
| Hilltops | the average of the neighbouring homes (6m where there are none) | 3m | 3m |
| Hornsby | 7.6m | 0.9m | 3m |
| Hunter's Hill | the average of the neighbouring homes | 1.5m, plus 0.33m for every metre of wall above 4.5m | 6m |
| Inner West | No controls for a duplex | ||
| Inverell | the average of the neighbouring homes (4.5m where there are none) | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Junee | at least 4.5m, or the street's established building line where that is further back | 0.9m | 0.9m |
| Kempsey | 5m | 0.9m | 3m |
| Kiama | at least 4.5m, or the street's established building line where that is further back | inside a plane rising at 45° from 5m above the boundary, and at least 0.9m | 6m |
| Ku-ring-gai | 12m | 1.5m on lots up to 24.99m wide, 1.5m on lots up to 36m wide, 2.5m on wider lots | 12m |
| Kyogle | the average of the neighbouring homes (3.5m where there are none) on lots up to 200.99m², the average of the neighbouring homes (4m where there are none) on lots up to 300m², the average of the neighbouring homes (4.5m where there are none) on lots up to 499.99m², the average of the neighbouring homes (4.5m where there are none) on lots up to 899.99m², the average of the neighbouring homes (5.5m where there are none) on larger lots | 0.9m, plus 0.25m for every metre of wall above 4.5m on lots up to 499.99m²; 0.9m on larger lots | 3m on lots up to 200.99m², 3m on lots up to 300m², 4m on lots up to 400m², 4.5m on lots up to 499.99m², 6m on larger lots |
| Lachlan | 6m | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Lake Macquarie | 4m | 0.9m | 3m |
| Lane Cove | the average of the neighbouring homes (7.5m where there are none) | 1.2m | 6m |
| Leeton | the average of the neighbouring homes (4.5m where there are none) on lots up to 749.99m², no figure on lots up to 750m², the average of the neighbouring homes (6m where there are none) on larger lots | 0.9m on lots up to 749.99m², no figure on lots up to 750m², 0.9m on larger lots | 3m on lots up to 749.99m², no figure on lots up to 750m², 5m on larger lots |
| Lismore | 6m | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Lithgow City | at least 4.5m, or the street's established building line where that is further back | 1.5m | 4.5m |
| Liverpool | 4.5m | 0.9m | 4m |
| Liverpool Plains | 4.5m | 1m | 1m |
| Lockhart | not set by the DCP: ask the council | left to the Building Code (0.9m) | not set by the DCP: ask the council |
| Maitland | the average of the neighbouring homes (4.5m where there are none) | inside a plane rising at 45° from 3m above the boundary, and at least 0.9m | 4m |
| MidCoast | 5m | 0.9m | 0.9m |
| Mid-Western Regional | 4.5m on lots up to 899.99m²; 6.5m on lots up to 1,999.99m²; no figure on larger lots | 0.9m on lots up to 899.99m²; 0.9m on lots up to 1,999.99m²; no figure on larger lots | 0.9m on lots up to 899.99m²; 0.9m on lots up to 1,999.99m²; no figure on larger lots |
| Moree Plains | the average of the neighbouring homes (6m where there are none) | 0.9m, plus 0.5m for every metre of wall above 3.5m | 2.4m, plus 0.5m for every metre of wall above 3.5m |
| Mosman | the average of the neighbouring homes | 0.9m | the average of the neighbouring homes |
| Murray River | the average of the neighbouring homes (3m on lots up to 450m²; 4.5m on lots up to 1,000m²; 6.5m on lots up to 1,500m²; 8.5m on lots up to 1,800m²; 10m on larger lots where there are none) | left to the Building Code (0.9m) on lots up to 1,800m²; 3m on lots up to 4,000m²; 5m on larger lots | left to the Building Code (0.9m) on lots up to 1,800m²; 5m on lots up to 4,000m²; 10m on larger lots |
| Murrumbidgee | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Muswellbrook | the average of the neighbouring homes (4.5m where there are none) | 0.9m, plus 0.3m for every metre of wall above 3m | 0.9m, plus 0.3m for every metre of wall above 3m |
| Nambucca Valley | the average of the neighbouring homes (4.5m where there are none) | 0.9m, plus 0.25m for every metre of wall above 3.8m | not set by the DCP: ask the council |
| Narrabri | 3m on lots up to 450m², 6m on larger lots | 0.9m | 0.9m on lots up to 450m², 3m on larger lots |
| Narrandera | the average of the neighbouring homes (5m where there are none) | not set by the DCP: ask the council | 5m |
| Narromine | the average of the neighbouring homes (7.5m where there are none) | left to the Building Code (0.9m) | 4m |
| Newcastle | the average of the neighbouring homes (4.5m where there are none) | inside a plane rising at 75.96° from 0.9m above the boundary, and at least 0.9m | 3m |
| North Sydney | the average of the neighbouring homes | 0.9m | the average of the neighbouring homes |
| Northern Beaches | 6.5m | 2.5m to one side, inside a plane rising at 45° from 4m above the boundary, and at least 1m to the other | 6m |
| Oberon | 6m | inside a plane rising at 45° from 1.5m above the boundary | inside a plane rising at 45° from 1.5m above the boundary |
| Orange | the average of the neighbouring homes (4.5m where there are none) | inside a plane rising at 45° from 2.5m above the boundary, and at least 0.9m | inside a plane rising at 45° from 2.5m above the boundary |
| Parkes | the average of the neighbouring homes (4.5m where there are none) on lots up to 599.99m², the average of the neighbouring homes (6m where there are none) on larger lots | 0.9m | 3m on lots up to 599.99m², 5m on larger lots |
| Penrith | at least 5.5m, or the street's established building line where that is further back | inside a plane rising at 45° from 1.8m above the boundary, and at least 0.9m | 4m |
| Port Macquarie-Hastings | 4.5m | 0.9m | 4m |
| Port Stephens | the average of the neighbouring homes (4.5m where there are none) on lots up to 1,000m²; the average of the neighbouring homes (10m where there are none) on larger lots | 0.9m on lots up to 1,000m²; 5m on larger lots | 2m on lots up to 1,000m²; 5m on larger lots |
| Queanbeyan-Palerang Regional | 6m | 3m | 3m |
| Randwick | the average of the neighbouring homes (6m where there are none) | no figure on lots up to 5.99m wide, 0.9m on lots up to 8.99m wide, 0.9m on lots up to 11.99m wide, 1.2m on wider lots | 25% of the lot depth on lots up to 32m deep, 8m on deeper lots |
| Richmond Valley | the average of the neighbouring homes (6m where there are none) | 0.9m, plus 0.25m for every metre of wall above 3.5m | 3m |
| Ryde | 6m | 0.9m | 25% of the lot depth, and at least 8m |
| Shellharbour | 4.5m | 0.9m | 3m |
| Shoalhaven | 5m on lots up to 599.99m², 6m on lots up to 900m², 7.5m on larger lots | 0.9m for the first 20m from the front, then 1.5m | 3m |
| Singleton | 6m on lots up to 24.99m wide, 5.5m on wider lots | 0.9m | 3m, plus 1m for every metre of wall above 5m |
| Snowy Monaro Regional | 6m | 0.9m | 3m |
| Snowy Valleys | the average of the neighbouring homes (no figure on lots up to 599.99m²; 6m on lots up to 1,500m²; 10m on larger lots where there are none) | 0.9m | no figure on lots up to 599.99m²; 3m on lots up to 1,500m²; 10m on larger lots |
| Strathfield | the average of the neighbouring homes | 1.2m | 6m on lots up to 30m deep; 20% of the lot depth, and at least 6m on lots up to 50m deep; 10m on deeper lots |
| Sutherland Shire | the average of the neighbouring homes (7.5m where there are none) | 0.9m | 6m |
| Sydney | at least not set, or the street's established building line where that is further back | not set by the DCP: ask the council | at least not set, or the street's established building line where that is further back |
| Tamworth Regional | 4.5m | 1m | 1m |
| Temora | 6m | 0.9m | 3m |
| Tenterfield | at least 6m, or the street's established building line where that is further back | 1m | 1m |
| The Hills Shire | at least 4.5m, or the street's established building line where that is further back | inside a plane rising at 45° from 1.8m above the boundary, and at least 0.9m for the dwelling furthest from the street in a detached dual occupancy (0.9 m for an attached dual occupancy) | inside a plane rising at 45° from 1.8m above the boundary, and at least 0.9m for the dwelling furthest from the street in a detached dual occupancy (0.9 m for an attached dual occupancy) |
| Tweed | the average of the neighbouring homes (3.5m on lots up to 300m²; 4.5m on lots up to 600m²; 6m on lots up to 900m²; 6m on lots up to 1,500m²; 8m on larger lots where there are none) | 0.9m | 3m on lots up to 300m²; 4.5m on lots up to 600m²; 4.5m on lots up to 900m²; 5m on lots up to 1,500m²; 10m on larger lots |
| Upper Hunter | the average of the neighbouring homes (4.5m where there are none) | 1m | 3m |
| Upper Lachlan Shire | the average of the neighbouring homes (4.5m where there are none) on lots up to 799.99m², no figure on lots up to 800m², the average of the neighbouring homes (6m where there are none) on larger lots | 0.9m on lots up to 799.99m², no figure on lots up to 800m², 0.9m on larger lots | 3m on lots up to 799.99m², no figure on lots up to 800m², 5m on larger lots |
| Uralla | the average of the neighbouring homes (6m where there are none) | 0.9m | 1.5m |
| Wagga Wagga | at least 6m, or the street's established building line where that is further back on lots up to 1,999.99m²; no figure on larger lots | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Walcha | the average of the neighbouring homes (6m where there are none) | 0.9m | 0.9m |
| Walgett | 4.5m | 1m | 1m |
| Warren | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Warrumbungle | the average of the neighbouring homes (6m where there are none) | 3m | 4m |
| Waverley | the average of the neighbouring homes | 0.9m | the average of the neighbouring homes |
| Weddin | 6m | 0.9m | 0.9m |
| Wentworth | the average of the neighbouring homes (6m where there are none) | 3.5m to one side, 1m to the other | 3m |
| Willoughby | the average of the neighbouring homes (no figure on lots up to 699m²; 4.5m on lots up to 900m²; 6.5m on lots up to 1,500m²; 10m on larger lots where there are none) | 0.9m, plus 0.25m for every metre of wall above 4.5m on lots up to 24m wide; 1.5m, plus 0.25m for every metre of wall above 4.5m on lots up to 36m wide; 2.5m on wider lots | no figure on lots up to 699m²; 3m on lots up to 900m²; 5m on lots up to 1,500m²; 10m on larger lots |
| Wingecarribee | the average of the neighbouring homes (4.5m on lots up to 899.99m²; 6.5m on lots up to 1,500m²; 15m on larger lots where there are none) | 0.9m on lots up to 899.99m²; 1.5m on lots up to 1,500m²; 2.5m on larger lots | 5.1m on lots up to 899.99m²; 7.1m on lots up to 1,500m²; 12.1m on larger lots |
| Wollondilly | the average of the neighbouring homes (4.5m where there are none) | 0.9m | 3m |
| Wollongong | 6m | 0.9m | 0.9m |
| Woollahra | the average of the neighbouring homes | 0.9m on lots up to 8.99m wide, 1.1m on lots up to 10.99m wide, 1.3m on lots up to 12.99m wide, 1.5m on lots up to 14.99m wide, 1.9m on lots up to 16.99m wide, 2.3m on lots up to 18.99m wide, 2.7m on lots up to 20.99m wide, 3.1m on lots up to 22.99m wide, 3.4m on lots up to 24.99m wide, 3.75m on lots up to 29.99m wide, 4.5m on wider lots | 25% of the lot depth |
| Yass Valley | no figure on lots up to 399.99m²; the average of the neighbouring homes (4.5m where there are none) on lots up to 900m²; the average of the neighbouring homes (6.5m where there are none) on lots up to 1,500m²; the average of the neighbouring homes (10m where there are none) on larger lots | 1.5m | no figure on lots up to 599.99m²; 3m on lots up to 899.99m²; 5m on lots up to 1,500m²; 10m on larger lots |
What else do people ask?
Can the council approve a duplex closer to the boundary than its DCP says?
It can. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.
Do duplex setbacks apply to sheds, pools and fences?
No. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.
Where does this information come from?
These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.