Skip to main content

How close to the boundary can a duplex be in Junee?

Junee Council's main plan, Junee Shire DCP 2021, Part C3 (single dwellings in villages) and Part C6 (medium density), RU5 Village, asks a single storey duplex for these setbacks: front at least 4.5m, or the street's established building line where that is further back; side 0.9m; and rear 0.9m.

In Junee the setbacks for a duplex come from Junee Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page is a first look: enter your address and the Site Checker opens at the setbacks for your lot, with the duplex first.

Check your address

NSW addresses only. Free, and no sign up.

What setbacks does Junee Council's main plan set for a duplex?

The table gives Junee Shire DCP 2021, Part C3 (single dwellings in villages) and Part C6 (medium density), RU5 Village's one and two storey figures and the clause each comes from. The plan covers this land: Land zoned RU5 Village: Junee town and the villages of Old Junee, Illabo and Bethungra, outside the Junee Heritage Conservation Area.

Junee Shire DCP 2021, Part C3 (single dwellings in villages) and Part C6 (medium density), RU5 Village: setbacks for a duplex
SetbackOne storeyTwo storeysWhere in the plan
Frontat least 4.5m, or the street's established building line where that is further backat least 6m, or the street's established building line where that is further backPart C6.5 Setbacks, Performance Criteria table, Primary Street Front Setback
Side0.9m1.5mPart C6.5 Setbacks, Performance Criteria table, Side and Rear Boundary
Rear0.9m1.5mPart C6.5 Setbacks, Performance Criteria table, Side and Rear Boundary
Corner block, second street3m4.5mPart C6.5 Setbacks, Performance Criteria table, Secondary Street Front Setback

Which DCP applies to my block in Junee?

It depends on where the lot is. Junee Shire DCP 2021, Part C3 (single dwellings in villages) and Part C6 (medium density), RU5 Village is Junee Council's main plan, and 6 other plans cover a duplex on particular land, such as a precinct, an estate, rural land or a former council area. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot. The table lists each plan with its one storey figures.

Other plans in Junee that cover a duplex
PlanWhere it appliesFrontSideRearSecond street
Junee Shire DCP 2021, Parts C3, C6 and H5 (heritage conservation area), RU5 Village in the Junee Heritage Conservation AreaRU5 Village land inside the Junee Heritage Conservation Area (Junee LEP 2012 Heritage Map, "C1").the average of the neighbouring homes (4.5m where there are none)0.9m0.9m3m
Junee Shire DCP 2021, Part C3 (Crawley Estate) and Part C6R5 Large Lot Residential lots in the Crawley Estate (Figure 3): De Salis Drive, Gwynne Place, Loughan Road and the east end of Smythe Road, between the Olympic Highway and the RU5 subdivision at Hilton Place, west of Junee town.at least 4.5m, or the street's established building line where that is further back0.9m0.9m3m
Junee Shire DCP 2021, Part C3 (Tathra Estate) and Part C6R5 Large Lot Residential lots in the Tathra Drive Estate (Figure 3): Tathra Drive off Gundagai Road, east of Junee town.at least 4.5m, or the street's established building line where that is further back0.9m0.9m3m
Junee Shire DCP 2021, Part C3 (Wantabadgery) and Part C6R5 Large Lot Residential land at Wantabadgery (the only R5 zone polygon in the locality, 210 ha).at least 4.5m, or the street's established building line where that is further back0.9m0.9m3m
Junee Shire DCP 2021, Part C4 (large lot and rural dwellings) and Part C6, R5 Large Lot ResidentialR5 Large Lot Residential land outside the Crawley and Tathra Drive Estates and Wantabadgery: the rest of the R5 land around Junee (west along Walster Street and south of the Olympic Highway, north of the Tathra estate to Kinvara Drive), Old Junee and Illabo.20m10m10m20m
Junee Shire DCP 2021, Part C4 (large lot and rural dwellings) and Part C6, RU1 Primary ProductionLand zoned RU1 Primary Production (most of the shire).20m50m50m20m

What are the complying development setbacks for a duplex?

If you build a duplex with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, the setbacks come from the state codes, not from the council's DCP, and they depend on the lot's area and width. The table shows the complying development (CDC) figures the Site Checker uses for three example lots: 450m² (15m wide, 30m deep), 600m² (15m wide, 40m deep) and 1,000m² (20m wide, 50m deep). Your own lot's figures are in its report, and Can I use complying development on my block? explains which lots qualify.

Complying development (CDC) setbacks for a duplex on three example lots
Example lotFrontSideRearCorner block, second street
450m² (15m wide, 30m deep)4.5m0.9m (1.5m at two storeys)3m (8m at two storeys)2m
600m² (15m wide, 40m deep)4.5m0.9m (1.5m at two storeys)3m (8m at two storeys)2m
1,000m² (20m wide, 50m deep)6.5m0.9m (1.5m at two storeys)5m (12m at two storeys)3m

What if my block is on a corner?

Junee Shire DCP 2021, Part C3 (single dwellings in villages) and Part C6 (medium density), RU5 Village sets a separate setback for a duplex from the second street, the side street of a corner block: 3m for one storey, 4.5m for two storeys (Part C6.5 Setbacks, Performance Criteria table, Secondary Street Front Setback). The complying development figure for the second street is in the CDC table above.

Does a two storey duplex need bigger setbacks?

Yes, under Junee Shire DCP 2021, Part C3 (single dwellings in villages) and Part C6 (medium density), RU5 Village: the front setback goes from at least 4.5m, or the street's established building line where that is further back to at least 6m, or the street's established building line where that is further back; the side setback goes from 0.9m to 1.5m; the rear setback goes from 0.9m to 1.5m; the corner block, second street setback goes from 3m to 4.5m. Under complying development, the two storey figures are in the CDC table above.

What else do people ask?

Can Junee Council approve a duplex closer to the boundary?

It can. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more. A complying development certificate has no such room: the design meets the code's setbacks or it is not complying development.

Do these setbacks apply to a shed, pool or fence in Junee?

No. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.

When were the setbacks on this page checked?

We last read Junee Council's plans on 12 November 2026. Each figure names the clause it came from, and each plan links to the council's own document, so you can check it against the current version.

Where does this information come from?

These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.

What else can I check?

Check what applies to your block