Skip to main content

How close to the boundary can a duplex be in Bathurst Regional?

Bathurst Regional Council's main plan, Bathurst Regional DCP 2014, Chapter 4 Residential Development (Zone R1), asks a single storey duplex for these setbacks: front at least 6m, or the street's established building line where that is further back; side left to the Building Code (0.9m); and rear left to the Building Code (0.9m).

In Bathurst Regional the setbacks for a duplex come from Bathurst Regional Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page is a first look: enter your address and the Site Checker opens at the setbacks for your lot, with the duplex first.

Check your address

NSW addresses only. Free, and no sign up.

What setbacks does Bathurst Regional Council's main plan set for a duplex?

The table gives Bathurst Regional DCP 2014, Chapter 4 Residential Development (Zone R1)'s one and two storey figures and the clause each comes from. The plan covers this land: Land in Zone R1 General Residential outside the Bathurst Heritage Conservation Area (LEP C1) and outside the Laffing Waters Master Plan Precinct (Chapter 17), including R1 land in the Kelso and Perthville heritage conservation areas.

Bathurst Regional DCP 2014, Chapter 4 Residential Development (Zone R1): setbacks for a duplex
SetbackOne storeyTwo storeysWhere in the plan
Frontat least 6m, or the street's established building line where that is further backat least 6m, or the street's established building line where that is further backBathurst Regional DCP 2014, Ch 4, s 4.4.2 Front Building Line Setback
Sideleft to the Building Code (0.9m)left to the Building Code (0.9m)Bathurst Regional DCP 2014, Ch 4, s 4.4.2 Side and Rear Building Line Setbacks
Rearleft to the Building Code (0.9m)left to the Building Code (0.9m)Bathurst Regional DCP 2014, Ch 4, s 4.4.2 Side and Rear Building Line Setbacks
Corner block, second street2m2mBathurst Regional DCP 2014, Ch 4, s 4.4.2 Front Building Line Setback (corner allotments)

Which DCP applies to my block in Bathurst Regional?

It depends on where the lot is. Bathurst Regional DCP 2014, Chapter 4 Residential Development (Zone R1) is Bathurst Regional Council's main plan, and 5 other plans cover a duplex on particular land, such as a precinct, an estate, rural land or a former council area. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot. The table lists each plan with its one storey figures.

Other plans in Bathurst Regional that cover a duplex
PlanWhere it appliesFrontSideRearSecond street
Bathurst Regional DCP 2014, Chapters 4 and 5 (Zones E1 and E2)Land in Zones E1 Local Centre and E2 Commercial Centre outside the Bathurst Heritage Conservation Area (LEP C1) (for example the Kelso and Laffing Waters local centres).at least 6m, or the street's established building line where that is further backleft to the Building Code (0.9m)left to the Building Code (0.9m)2m
Bathurst Regional DCP 2014, Bathurst Heritage Conservation Area (Zones R1, E1 and E2)Land in Zones R1, E1 and E2 inside the Bathurst Heritage Conservation Area (LEP Schedule 5, C1), including the Mid Century Heritage Precincts (DCP Map 33).the average of the neighbouring homesleft to the Building Code (0.9m)left to the Building Code (0.9m)not set
Bathurst Regional DCP 2014, Chapter 7 Village Development (Zone RU5)Land in Zone RU5 Village, inside and outside the LEP heritage conservation areas (the Hill End, Sofala, Rockley, Wattle Flat, Peel and Trunkey Creek conservation areas, and Georges Plains, Yetholme, Raglan and the other villages).the average of the neighbouring homesleft to the Building Code (0.9m)left to the Building Code (0.9m)not set
Bathurst Regional DCP 2014, Chapter 17 Laffing Waters, Conventional Density HousingThe Conventional Density Housing Land Use Area of the Laffing Waters Master Plan Precinct, Kelso (DCP Map No. 4A), zoned R1.5m on lots up to 21.99m wide, 6m on wider lots0.9m3m0.9m on lots up to 21.99m wide, 2m on wider lots
Bathurst Regional DCP 2014, Chapter 17 Laffing Waters, Low Density HousingThe Low Density Housing Land Use Area of the Laffing Waters Master Plan Precinct, Kelso (DCP Map No. 4A), zoned R1.6m0.9m3m2m

What are the complying development setbacks for a duplex?

If you build a duplex with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, the setbacks come from the state codes, not from the council's DCP, and they depend on the lot's area and width. The table shows the complying development (CDC) figures the Site Checker uses for three example lots: 450m² (15m wide, 30m deep), 600m² (15m wide, 40m deep) and 1,000m² (20m wide, 50m deep). Your own lot's figures are in its report, and Can I use complying development on my block? explains which lots qualify.

Complying development (CDC) setbacks for a duplex on three example lots
Example lotFrontSideRearCorner block, second street
450m² (15m wide, 30m deep)4.5m0.9m (1.5m at two storeys)3m (8m at two storeys)2m
600m² (15m wide, 40m deep)4.5m0.9m (1.5m at two storeys)3m (8m at two storeys)2m
1,000m² (20m wide, 50m deep)6.5m0.9m (1.5m at two storeys)5m (12m at two storeys)3m

What if my block is on a corner?

Bathurst Regional DCP 2014, Chapter 4 Residential Development (Zone R1) sets a separate setback for a duplex from the second street, the side street of a corner block: 2m (Bathurst Regional DCP 2014, Ch 4, s 4.4.2 Front Building Line Setback (corner allotments)). The complying development figure for the second street is in the CDC table above.

Does a two storey duplex need bigger setbacks?

No. Bathurst Regional DCP 2014, Chapter 4 Residential Development (Zone R1) sets the same figures for a one or two storey duplex. Under complying development, the two storey figures are in the CDC table above.

What else do people ask?

Can Bathurst Regional Council approve a duplex closer to the boundary?

It can. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more. A complying development certificate has no such room: the design meets the code's setbacks or it is not complying development.

Do these setbacks apply to a shed, pool or fence in Bathurst Regional?

No. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.

When were the setbacks on this page checked?

We last read Bathurst Regional Council's plans on 12 November 2026. Each figure names the clause it came from, and each plan links to the council's own document, so you can check it against the current version.

Where does this information come from?

These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.

What else can I check?

Check what applies to your block