What are the setbacks for a granny flat in NSW?
Written by Shea Cullen, architect, for Dudils.
A setback is how far a home must sit from each boundary of its lot. For a granny flat in NSW they come from one of two places: the state's complying development codes, or the council's development control plan (DCP) when you lodge a development application.
This page gives the state figures and every council's main figures, and links each council's own page.
NSW addresses only. Free, and no sign up.
How close to the boundary can a granny flat be in NSW?
As complying development, a granny flat on a 600m² (15m wide, 40m deep) lot can sit 0.9m (1.5m at two storeys) from the side boundaries and 3m from the rear, with a 4.5m front setback. Those are the figures the Site Checker reads from the state codes; the table gives them for three example lots, 450m² (15m wide, 30m deep), 600m² (15m wide, 40m deep) and 1,000m² (20m wide, 50m deep).
Under a development application the council's DCP sets them instead, and the councils differ. Of the 104 councils whose main plan sets a side setback for a granny flat, 45 ask for 0.9m, the most common single figure. Of the 105 councils whose main plan sets a rear setback for a granny flat, 22 ask for 3m, the most common single figure.
| Example lot | Front | Side | Rear | Corner block, second street |
|---|---|---|---|---|
| 450m² (15m wide, 30m deep) | 4.5m | 0.9m (1.5m at two storeys) | 3m | 2m |
| 600m² (15m wide, 40m deep) | 4.5m | 0.9m (1.5m at two storeys) | 3m | 2m |
| 1,000m² (20m wide, 50m deep) | 6.5m | 1.5m | 5m | 3m |
What is the rear setback for a granny flat in NSW?
As complying development it is 3m on the 450m² lot, 3m on the 600m² lot and 5m on the 1,000m² lot, as the Site Checker reads the code. Under a development application the council sets it. Of the 105 councils whose main plan sets a rear setback for a granny flat, 22 ask for 3m, the most common single figure, and the rest use other figures or rules.
Can a granny flat be built on the boundary?
Not as complying development: on the example lots the side setback is at least 0.9m. None of the 104 councils whose main plan sets a side setback for a granny flat set 0m for a side boundary anywhere in their side rules. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more. A wall closer than 0.9m to a boundary also needs fire rated construction under the Building Code.
Does a two storey granny flat need bigger setbacks?
Under complying development, yes: on a 600m² (15m wide, 40m deep) lot the front setback is 4.5m, the side 0.9m (1.5m at two storeys) and the rear 3m. Under a development application it depends on the council: 59 of the 128 councils' main plans set a different front, side or rear figure for two storeys, and each council's page shows both.
Do council rules or complying development apply to my granny flat?
It depends on how you get approval. With a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, the state codes set the setbacks and the council's plan does not apply. With a development application, the council's development control plan (DCP), the council's own rules for the design of homes in its area, sets them. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.
13 of the 128 councils' main plans set no front, side or rear setback for a granny flat; there, ask the council what it expects.
What does each council ask for a granny flat?
The table gives each council's main plan at one storey; follow a council for its two storey figures, its clauses and its other plans. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot.
| Council | Front | Side | Rear |
|---|---|---|---|
| Albury City | the average of the neighbouring homes (4m where there are none) | 0.9m | 2m |
| Armidale Regional | 4.5m | 0.9m | 0.9m |
| Ballina | at least 4.5m, or the street's established building line where that is further back | 0.9m to one side, 0.9m to the other | 0.9m |
| Balranald | 6m | not set by the council's policy: ask the council | not set by the council's policy: ask the council |
| Bathurst Regional | at least 6m, or the street's established building line where that is further back | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Bayside | the average of the neighbouring homes (6m where there are none) | 0.9m | 0.9m |
| Bega Valley | no figure on lots up to 349.99m², the average of the neighbouring homes (4.5m where there are none) on lots up to 550m², the average of the neighbouring homes (5m where there are none) on lots up to 900m², the average of the neighbouring homes (6m where there are none) on larger lots | 0.9m | no figure on lots up to 349.99m², 4m on lots up to 900m², 5m on larger lots |
| Bellingen | at least 4.5m, or the street's established building line where that is further back | inside a plane rising at 35° from 3m above the boundary, and at least 0.9m | inside a plane rising at 35° from 3m above the boundary |
| Berrigan | the average of the neighbouring homes (4.5m where there are none) | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Blacktown | 6m | 0.9m | 0.9m |
| Bland | 5m | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Blayney | at least 4.5m, or the street's established building line where that is further back | 1.5m | 1.5m |
| Blue Mountains | the average of the neighbouring homes (8m where there are none) | 1m | 4m |
| Bogan | 6m | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Bourke | 4.5m | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Brewarrina | 6m | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Broken Hill | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Burwood | the average of the neighbouring homes | 0.9m | 3m |
| Byron | 4.5m | inside a plane rising at 45° from 1.8m above the boundary, and at least 1.5m | inside a plane rising at 45° from 1.8m above the boundary, and at least 1.5m |
| Cabonne | 8m | not set by the council's policy: ask the council | not set by the council's policy: ask the council |
| Camden | the average of the neighbouring homes (4.5m on lots up to 900m²; 6.5m on lots up to 1,500m²; 10m on larger lots where there are none) | 0.9m | 4m |
| Campbelltown | at least 5.5m, or the street's established building line where that is further back | 0.9m | 3m |
| Canada Bay | at least 4.5m, or the street's established building line where that is further back | 1.5m | 3m |
| Canterbury-Bankstown | 5.5m | 0.9m | 0.9m |
| Carrathool | 6m | not set by the council's policy: ask the council | not set by the council's policy: ask the council |
| Central Coast | 3m on lots up to 300m², the average of the neighbouring homes (4.5m where there are none) on larger lots | 0.9m, plus 0.25m for every metre of wall above 4.5m | 3m |
| Central Darling | 6m | 1.5m | 4.5m |
| Cessnock | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Parramatta | at least 6m, or the street's established building line where that is further back | 0.9m | 3m |
| Clarence Valley | at least 6m, or the street's established building line where that is further back | 0.9m | 0.9m |
| Cobar | not set (the council has no DCP): ask the council | not set (the council has no DCP): ask the council | not set (the council has no DCP): ask the council |
| Coffs Harbour | 4.5m | 0.9m | 3m |
| Coolamon | 8m | 0.9m | 0m |
| Coonamble | 7.5m | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Cootamundra-Gundagai Regional | the average of the neighbouring homes (4.5m on lots up to 599.99m²; 4.5m on lots up to 899.99m²; 6.5m on lots up to 1,499.99m²; 10m on larger lots where there are none) | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Cowra | the average of the neighbouring homes (6m where there are none) | 0.9m | 3m |
| Cumberland | 6m | 0.9m | 0.9m |
| Dubbo Regional | the average of the neighbouring homes (4.5m where there are none) | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Dungog | 6m | inside a plane rising at 45° from 1.8m above the boundary, and at least 0.9m | inside a plane rising at 45° from 1.8m above the boundary, and at least 0.9m |
| Edward River | the average of the neighbouring homes (5m where there are none) | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Eurobodalla | the average of the neighbouring homes (5.5m where there are none) on lots up to 2,499.99m²; 7m on lots up to 4,999.99m²; the average of the neighbouring homes (5.5m where there are none) on larger lots | 0.9m on lots up to 2,499.99m²; 5m on lots up to 4,999.99m²; 0.9m on larger lots | 3m on lots up to 2,499.99m²; 5m on lots up to 4,999.99m²; 3m on larger lots |
| Fairfield | not set by the DCP: ask the council | 0.9m | 0.9m |
| Federation | the average of the neighbouring homes (3m on lots up to 300m²; 4.5m on lots up to 900m²; 6.5m on lots up to 1,500m²; 10m on larger lots where there are none) | 0.9m, plus 0.25m for every metre of wall above 5.5m on lots up to 10m wide; 0.9m, plus 0.25m for every metre of wall above 4.5m on lots up to 18m wide; 1.5m, plus 0.25m for every metre of wall above 4.5m on lots up to 24m wide; 2.5m on wider lots | 3m on lots up to 300m²; 3m on lots up to 900m²; 5m on lots up to 1,500m²; 10m on larger lots |
| Forbes | the average of the neighbouring homes (6m where there are none) on lots up to 50m deep, the average of the neighbouring homes (8m where there are none) on lots up to 70m deep, the average of the neighbouring homes (10m where there are none) on deeper lots | 0.9m | 0.9m |
| Georges River | at least 4.5m, or the street's established building line where that is further back | 1.5m | 1.5m |
| Gilgandra | at least 7.5m, or the street's established building line where that is further back | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Glen Innes Severn | the average of the neighbouring homes (6m where there are none) | 0.9m | 0.9m |
| Goulburn Mulwaree | 4.5m | 1m | 6m |
| Greater Hume Shire | the average of the neighbouring homes (4.5m where there are none) | 2m | 2m |
| Griffith | 6m | 0.9m | 2m |
| Gunnedah | the average of the neighbouring homes (6.5m where there are none) | 0.9m | 0.9m |
| Gwydir | not set (the council has no DCP): ask the council | not set (the council has no DCP): ask the council | not set (the council has no DCP): ask the council |
| Hawkesbury | the average of the neighbouring homes (7.5m where there are none) | inside a plane rising at 45° from 1.8m above the boundary | inside a plane rising at 45° from 1.8m above the boundary |
| Hay | 5m | 0.9m | 0.9m |
| Hilltops | the average of the neighbouring homes (6m where there are none) | 3m | 3m |
| Hornsby | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Hunter's Hill | the average of the neighbouring homes | 1.5m | 6m |
| Inner West | the average of the neighbouring homes | 1.5m | the average of the neighbouring homes |
| Inverell | the average of the neighbouring homes (4.5m where there are none) | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Junee | at least 4.5m, or the street's established building line where that is further back | 0.9m | 0.9m |
| Kempsey | at least 5m, or the street's established building line where that is further back | 0.9m | 3m |
| Kiama | at least 4.5m, or the street's established building line where that is further back | inside a plane rising at 45° from 5m above the boundary, and at least 0.9m | 6m |
| Ku-ring-gai | 12m | 1.5m on lots up to 19.99m wide; 1.89m on lots up to 21m wide; 1.98m on lots up to 22m wide; 2.07m on lots up to 23m wide; 2.16m on lots up to 24m wide; 2.25m on lots up to 25m wide; 2.34m on lots up to 26m wide; 2.43m on lots up to 27m wide; 2.52m on lots up to 28m wide; 2.61m on lots up to 29m wide; 2.7m on lots up to 30m wide; 2.79m on lots up to 31m wide; 2.88m on lots up to 32m wide; 2.97m on lots up to 33m wide; 3.06m on lots up to 34m wide; 3.15m on lots up to 35m wide; 3.24m on lots up to 36m wide; 3.33m on lots up to 37m wide; 3.42m on lots up to 38m wide; 3.51m on lots up to 39m wide; 3.6m on lots up to 40m wide; 3.69m on lots up to 41m wide; 3.78m on lots up to 42m wide; 3.87m on lots up to 43m wide; 3.96m on lots up to 44m wide; 4.05m on lots up to 45m wide; 4.14m on lots up to 46m wide; 4.23m on lots up to 47m wide; 4.32m on lots up to 48m wide; 4.41m on lots up to 49m wide; 4.5m on lots up to 50m wide; 4.59m on lots up to 51m wide; 4.68m on lots up to 52m wide; 4.77m on lots up to 53m wide; 4.86m on lots up to 54m wide; 4.95m on lots up to 55m wide; 5.04m on lots up to 56m wide; 5.13m on lots up to 57m wide; 5.22m on lots up to 58m wide; 5.31m on lots up to 59m wide; 5.4m on lots up to 60m wide; 5.85m on lots up to 65m wide; 6.3m on lots up to 70m wide; 6.75m on lots up to 75m wide; 7.2m on lots up to 80m wide; 7.65m on lots up to 85m wide; 8.1m on lots up to 90m wide; 8.55m on lots up to 95m wide; 9m on lots up to 100m wide; 9m for a lot over 100 m wide, shown at the 100 m figure; the DCP asks for 9% of the actual site width on wider lots | 6m |
| Kyogle | the average of the neighbouring homes (3.5m where there are none) on lots up to 200.99m²; the average of the neighbouring homes (4m where there are none) on lots up to 300m²; the average of the neighbouring homes (4.5m where there are none) on lots up to 499.99m²; at least 4.5m, or the street's established building line where that is further back on lots up to 899.99m²; at least 5.5m, or the street's established building line where that is further back on larger lots | 0.9m, plus 0.25m for every metre of wall above 4.5m on lots up to 499.99m²; 0.9m on larger lots | 3m on lots up to 200.99m², 3m on lots up to 300m², 4m on lots up to 400m², 4.5m on lots up to 499.99m², 3m on larger lots |
| Lachlan | 6m | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Lake Macquarie | 4m | 0.9m | 3m |
| Lane Cove | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Leeton | the average of the neighbouring homes (4.5m where there are none) on lots up to 749.99m², no figure on lots up to 750m², the average of the neighbouring homes (6m where there are none) on larger lots | 0.9m on lots up to 749.99m², no figure on lots up to 750m², 0.9m on larger lots | 3m on lots up to 749.99m², no figure on lots up to 750m², 5m on larger lots |
| Lismore | 6m | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Lithgow City | at least 4.5m, or the street's established building line where that is further back on lots up to 800m²; the average of the neighbouring homes (6m where there are none) on larger lots | 0.9m | 3m on lots up to 800m², 4m on larger lots |
| Liverpool | no figure on lots up to 399.99m², 4.5m on larger lots | no figure on lots up to 399.99m², 0.9m on larger lots | no figure on lots up to 399.99m², 4m on larger lots |
| Liverpool Plains | 4.5m | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Lockhart | not set by the DCP: ask the council | left to the Building Code (0.9m) | not set by the DCP: ask the council |
| Maitland | the average of the neighbouring homes (4.5m where there are none) | inside a plane rising at 45° from 3m above the boundary, and at least 0.9m | 3m on lots up to 899.99m²; 5m on lots up to 1,499.99m²; 10m on larger lots |
| MidCoast | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Mid-Western Regional | 4.5m on lots up to 899.99m²; 6.5m on lots up to 1,999.99m²; no figure on larger lots | 0.9m on lots up to 899.99m²; 0.9m on lots up to 1,999.99m²; no figure on larger lots | 0.9m on lots up to 899.99m²; 0.9m on lots up to 1,999.99m²; no figure on larger lots |
| Moree Plains | the average of the neighbouring homes (6m where there are none) | 0.9m, plus 0.5m for every metre of wall above 3.5m | 2.4m, plus 0.5m for every metre of wall above 3.5m |
| Mosman | the average of the neighbouring homes | 0.9m | the average of the neighbouring homes |
| Murray River | the average of the neighbouring homes (3m on lots up to 450m²; 4.5m on lots up to 1,000m²; 6.5m on lots up to 1,500m²; 8.5m on lots up to 1,800m²; 10m on larger lots where there are none) | left to the Building Code (0.9m) on lots up to 1,800m²; 3m on lots up to 4,000m²; 5m on larger lots | left to the Building Code (0.9m) on lots up to 1,800m²; 5m on lots up to 4,000m²; 10m on larger lots |
| Murrumbidgee | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Muswellbrook | the average of the neighbouring homes (4.5m where there are none) | 0.9m, plus 0.3m for every metre of wall above 3m | 0.9m, plus 0.3m for every metre of wall above 3m |
| Nambucca Valley | the average of the neighbouring homes (4.5m where there are none) | 0.9m, plus 0.25m for every metre of wall above 3.8m | not set by the DCP: ask the council |
| Narrabri | 3m on lots up to 450m², 4.5m on larger lots | 0.9m | 0.9m on lots up to 450m², 3m on larger lots |
| Narrandera | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Narromine | the average of the neighbouring homes (7.5m where there are none) | left to the Building Code (0.9m) | 4m |
| Newcastle | the average of the neighbouring homes (3m on lots up to 299.99m², 4.5m on larger lots where there are none) | inside a plane rising at 75.96° from 1.9m above the boundary, and at least 0.9m on lots up to 10.49m wide; inside a plane rising at 75.96° from 0.9m above the boundary, and at least 0.9m on wider lots | 3m |
| North Sydney | the average of the neighbouring homes | 0.9m | the average of the neighbouring homes |
| Northern Beaches | 6.5m | inside a plane rising at 45° from 4m above the boundary, and at least 0.9m | 6m |
| Oberon | 6m | inside a plane rising at 45° from 1.5m above the boundary | inside a plane rising at 45° from 1.5m above the boundary |
| Orange | the average of the neighbouring homes (4.5m where there are none) | inside a plane rising at 45° from 2.5m above the boundary, and at least 0.9m | inside a plane rising at 45° from 2.5m above the boundary |
| Parkes | the average of the neighbouring homes (4.5m where there are none) on lots up to 599.99m², the average of the neighbouring homes (6m where there are none) on larger lots | 0.9m | 3m on lots up to 599.99m², 5m on larger lots |
| Penrith | at least 5.5m, or the street's established building line where that is further back | inside a plane rising at 45° from 1.8m above the boundary, and at least 0.9m | 3m |
| Port Macquarie-Hastings | 4.5m | 0.9m | 4m |
| Port Stephens | the average of the neighbouring homes (4.5m where there are none) on lots up to 1,000m²; the average of the neighbouring homes (10m where there are none) on larger lots | 0.9m on lots up to 1,000m²; 5m on larger lots | 0.9m on lots up to 1,000m²; 5m on larger lots |
| Queanbeyan-Palerang Regional | not set by the DCP: ask the council | 0.9m | 3m |
| Randwick | the average of the neighbouring homes (6m where there are none) | not set by the DCP: ask the council | 3m |
| Richmond Valley | the average of the neighbouring homes (6m where there are none) | 0.9m, plus 0.25m for every metre of wall above 3.5m | 3m |
| Ryde | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Shellharbour | 4.5m | 0.9m | 3m |
| Shoalhaven | the average of the neighbouring homes (4.5m on lots up to 900m²; 6.5m on lots up to 1,500m²; 10m on larger lots where there are none) | 0.9m, plus 0.25m for every metre of wall above 3.8m on lots up to 900m²; 1.5m, plus 0.25m for every metre of wall above 3.8m on lots up to 1,500m²; 2.5m, plus 0.25m for every metre of wall above 3.8m on larger lots | 5.1m on lots up to 900m²; 7.1m on lots up to 1,500m²; 12.1m on larger lots |
| Singleton | 6m on lots up to 24.99m wide, 5.5m on wider lots | 0.9m | 3m, plus 1m for every metre of wall above 5m |
| Snowy Monaro Regional | 6m | 0.9m | 3m |
| Snowy Valleys | the average of the neighbouring homes (no figure on lots up to 199.99m²; 4.5m on lots up to 600m²; 6m on lots up to 1,500m²; 10m on larger lots where there are none) | 0.9m | no figure on lots up to 199.99m²; 3m on lots up to 300m²; 4.5m on lots up to 900m²; 5m on lots up to 1,500m²; 10m on larger lots |
| Strathfield | the average of the neighbouring homes | 1.5m | 3m |
| Sutherland Shire | the average of the neighbouring homes (7.5m where there are none) | 0.9m | 3m |
| Sydney | at least not set, or the street's established building line where that is further back | not set by the DCP: ask the council | at least not set, or the street's established building line where that is further back |
| Tamworth Regional | No controls for a granny flat | ||
| Temora | 6m | 0.9m | 3m |
| Tenterfield | at least 6m, or the street's established building line where that is further back | 1m | 1m |
| The Hills Shire | at least 10m, or the street's established building line where that is further back | 0.9m | 4m |
| Tweed | the average of the neighbouring homes (3.5m on lots up to 300m²; 4.5m on lots up to 600m²; 6m on lots up to 900m²; 6m on lots up to 1,500m²; 8m on larger lots where there are none) | 0.9m | 1.5m |
| Upper Hunter | the average of the neighbouring homes (4.5m where there are none) | 1m | 3m |
| Upper Lachlan Shire | the average of the neighbouring homes (4.5m where there are none) on lots up to 799.99m², no figure on lots up to 800m², the average of the neighbouring homes (6m where there are none) on larger lots | 0.9m on lots up to 799.99m², no figure on lots up to 800m², 0.9m on larger lots | 3m on lots up to 799.99m², no figure on lots up to 800m², 5m on larger lots |
| Uralla | the average of the neighbouring homes (6m where there are none) | 0.9m | 1.5m |
| Wagga Wagga | at least 6m, or the street's established building line where that is further back on lots up to 1,999.99m²; no figure on larger lots | not set by the DCP: ask the council | the average of the neighbouring homes (detached secondary dwellings) |
| Walcha | the average of the neighbouring homes (6m where there are none) | 0.9m | 0.9m |
| Walgett | 4.5m | left to the Building Code (0.9m) | left to the Building Code (0.9m) |
| Warren | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Warrumbungle | not set by the DCP: ask the council | not set by the DCP: ask the council | not set by the DCP: ask the council |
| Waverley | the average of the neighbouring homes | 0.9m | the average of the neighbouring homes |
| Weddin | 6m | 0.9m | 0.9m |
| Wentworth | the average of the neighbouring homes (6m where there are none) | 3.5m to one side, 1m to the other | 3m |
| Willoughby | the average of the neighbouring homes (3m on lots up to 300m²; 4.5m on lots up to 900m²; 6.5m on lots up to 1,500m²; 10m on larger lots where there are none) | 0.9m, plus 0.25m for every metre of wall above 5.5m on lots up to 10m wide; 0.9m, plus 0.25m for every metre of wall above 4.5m on lots up to 18m wide; 1.5m, plus 0.25m for every metre of wall above 4.5m on lots up to 24m wide; 2.5m on wider lots | 3m on lots up to 300m²; 3m on lots up to 900m²; 5m on lots up to 1,500m²; 10m on larger lots |
| Wingecarribee | the average of the neighbouring homes (4.5m on lots up to 899.99m²; 6.5m on lots up to 1,500m²; 15m on larger lots where there are none) | 0.9m on lots up to 899.99m²; 1.5m on lots up to 1,500m²; 2.5m on larger lots | 5.1m on lots up to 899.99m²; 7.1m on lots up to 1,500m²; 12.1m on larger lots |
| Wollondilly | the average of the neighbouring homes (3m where there are none) on lots up to 300m²; the average of the neighbouring homes (4.5m where there are none) on lots up to 900m²; the average of the neighbouring homes (6.5m where there are none) on lots up to 1,500m²; the average of the neighbouring homes (10m where there are none) on larger lots | 0.9m on lots up to 900m²; 1.5m on lots up to 1,500m²; 2.5m on larger lots | 3m on lots up to 900m²; 5m on lots up to 1,500m²; 10m on larger lots |
| Wollongong | 6m | 0.9m | 0.9m |
| Woollahra | the average of the neighbouring homes | 0.9m on lots up to 8.99m wide, 1.1m on lots up to 10.99m wide, 1.3m on lots up to 12.99m wide, 1.5m on lots up to 14.99m wide, 1.9m on lots up to 16.99m wide, 2.3m on lots up to 18.99m wide, 2.7m on lots up to 20.99m wide, 3.1m on lots up to 22.99m wide, 3.4m on lots up to 24.99m wide, 3.75m on lots up to 29.99m wide, 4.5m on wider lots | 25% of the lot depth |
| Yass Valley | no figure on lots up to 199.99m²; the average of the neighbouring homes (3m where there are none) on lots up to 300m²; the average of the neighbouring homes (4.5m where there are none) on lots up to 900m²; the average of the neighbouring homes (6.5m where there are none) on lots up to 1,500m²; the average of the neighbouring homes (10m where there are none) on larger lots | 0.9m, plus 0.25m for every metre of wall above 4.5m | 0.9m, plus 0.25m for every metre of wall above 4.5m |
What else do people ask?
Can the council approve a granny flat closer to the boundary than its DCP says?
It can. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.
Do granny flat setbacks apply to sheds, pools and fences?
No. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.
Where does this information come from?
These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.