Skip to main content

How close to the boundary can a granny flat be in Moree Plains?

Moree Plains Council's main plan, Moree Plains DCP 2013, Chapter 3 Residential Development (Zone R1 General Residential), asks a single storey granny flat for these setbacks: front the average of the neighbouring homes (6m where there are none); side 0.9m, plus 0.5m for every metre of wall above 3.5m; and rear 2.4m, plus 0.5m for every metre of wall above 3.5m.

In Moree Plains the setbacks for a granny flat come from Moree Plains Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page is a first look: enter your address and the Site Checker opens at the setbacks for your lot, with the granny flat first.

Check your address

NSW addresses only. Free, and no sign up.

What setbacks does Moree Plains Council's main plan set for a granny flat?

The table gives Moree Plains DCP 2013, Chapter 3 Residential Development (Zone R1 General Residential)'s one and two storey figures and the clause each comes from. The plan covers this land: Land zoned R1 General Residential.

Moree Plains DCP 2013, Chapter 3 Residential Development (Zone R1 General Residential): setbacks for a granny flat
SetbackOne storeyTwo storeysWhere in the plan
Frontthe average of the neighbouring homes (6m where there are none)the average of the neighbouring homes (6m where there are none)Chapter 3 Residential Development, Setbacks, Acceptable Solution 1, Table 3.2
Side0.9m, plus 0.5m for every metre of wall above 3.5m0.9m, plus 0.5m for every metre of wall above 3.5mChapter 3 Residential Development, Setbacks, Acceptable Solution 1, Table 3.2
Rear2.4m, plus 0.5m for every metre of wall above 3.5m2.4m, plus 0.5m for every metre of wall above 3.5mChapter 3 Residential Development, Setbacks, Acceptable Solution 1, Table 3.2
Corner block, second street4m4mChapter 3 Residential Development, Setbacks, Acceptable Solution 1, Table 3.2

Which DCP applies to my block in Moree Plains?

It depends on where the lot is. Moree Plains DCP 2013, Chapter 3 Residential Development (Zone R1 General Residential) is Moree Plains Council's main plan, and 4 other plans cover a granny flat on particular land, such as a precinct, an estate, rural land or a former council area. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot. The table lists each plan with its one storey figures.

Other plans in Moree Plains that cover a granny flat
PlanWhere it appliesFrontSideRearSecond street
Moree Plains DCP 2013, Chapter 3 Residential Development (Zone RU5 Village)Land zoned RU5 Village (the shire's villages).the average of the neighbouring homes (6m where there are none)0.9m, plus 0.5m for every metre of wall above 3.5m2.4m, plus 0.5m for every metre of wall above 3.5m4m
Moree Plains DCP 2013, Chapter 3 Residential Development (Zone R2 Low Density Residential)Land zoned R2 Low Density Residential.the average of the neighbouring homes (8m where there are none)1.6m, plus 0.5m for every metre of wall above 3.5m3.2m, plus 0.5m for every metre of wall above 3.5m6m
Moree Plains DCP 2013, Chapter 3 Residential Development (Zone R5 Large Lot Residential)Land zoned R5 Large Lot Residential.the average of the neighbouring homes (20m where there are none)10m10mnot set
Moree Plains DCP 2013, Chapter 9 Rural Development, Rural Dwellings (Zone RU1)Land zoned RU1 Primary Production.130mnot set by the DCP: ask the councilnot set by the DCP: ask the council130m

What are the complying development setbacks for a granny flat?

If you build a granny flat with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, the setbacks come from the state codes, not from the council's DCP, and they depend on the lot's area and width. The table shows the complying development (CDC) figures the Site Checker uses for three example lots: 450m² (15m wide, 30m deep), 600m² (15m wide, 40m deep) and 1,000m² (20m wide, 50m deep). Your own lot's figures are in its report, and Can I use complying development on my block? explains which lots qualify.

Complying development (CDC) setbacks for a granny flat on three example lots
Example lotFrontSideRearCorner block, second street
450m² (15m wide, 30m deep)4.5m0.9m (1.5m at two storeys)3m2m
600m² (15m wide, 40m deep)4.5m0.9m (1.5m at two storeys)3m2m
1,000m² (20m wide, 50m deep)6.5m1.5m5m3m

What if my block is on a corner?

Moree Plains DCP 2013, Chapter 3 Residential Development (Zone R1 General Residential) sets a separate setback for a granny flat from the second street, the side street of a corner block: 4m (Chapter 3 Residential Development, Setbacks, Acceptable Solution 1, Table 3.2). The complying development figure for the second street is in the CDC table above.

Does a two storey granny flat need bigger setbacks?

Yes, through the wall height: under Moree Plains DCP 2013, Chapter 3 Residential Development (Zone R1 General Residential) the side and rear setback grows as the wall gets taller. Under complying development, the two storey figures are in the CDC table above.

What else do people ask?

Can Moree Plains Council approve a granny flat closer to the boundary?

It can. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more. A complying development certificate has no such room: the design meets the code's setbacks or it is not complying development.

Do these setbacks apply to a shed, pool or fence in Moree Plains?

No. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.

When were the setbacks on this page checked?

We last read Moree Plains Council's plans on 12 November 2026. Each figure names the clause it came from, and each plan links to the council's own document, so you can check it against the current version.

Where does this information come from?

These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.

What else can I check?

Check what applies to your block