How close to the boundary can a granny flat be in Clarence Valley?
Clarence Valley Council's main plan, Clarence Valley Residential Zones DCP 2011, Part C (R1, R2, R3), asks a single storey granny flat for these setbacks: front at least 6m, or the street's established building line where that is further back; side 0.9m; and rear 0.9m.
In Clarence Valley the setbacks for a granny flat come from Clarence Valley Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page is a first look: enter your address and the Site Checker opens at the setbacks for your lot, with the granny flat first.
NSW addresses only. Free, and no sign up.
What setbacks does Clarence Valley Council's main plan set for a granny flat?
The table gives Clarence Valley Residential Zones DCP 2011, Part C (R1, R2, R3)'s one and two storey figures and the clause each comes from. The plan covers this land: Land zoned R1 General Residential, R2 Low Density Residential or R3 Medium Density Residential under Clarence Valley LEP 2011 (Residential Zones DCP A3, C16.2), except where a site part of the DCP sets its own setbacks: Angourie (Part Q), Glenreagh (Part R) and Ulmarra (Part U) village R2/R3 land, the Yamba Shores canal lots in Schedule C1 item 2, and the lots on the northern side of Queens Lane, Iluka.
| Setback | One storey | Two storeys | Where in the plan |
|---|---|---|---|
| Front | at least 6m, or the street's established building line where that is further back | at least 6m, or the street's established building line where that is further back | Residential Zones DCP 2011, Part C, C16.2 and C17.2 |
| Side | 0.9m | 1.5m | Residential Zones DCP 2011, Part C, C16.2, Table C5 |
| Rear | 0.9m | 1.5m | Residential Zones DCP 2011, Part C, C16.2, Table C5 |
| Corner block, second street | 3.5m | 3.5m | Residential Zones DCP 2011, Part C, C16.5 |
Which DCP applies to my block in Clarence Valley?
It depends on where the lot is. Clarence Valley Residential Zones DCP 2011, Part C (R1, R2, R3) is Clarence Valley Council's main plan, and 8 other plans cover a granny flat on particular land, such as a precinct, an estate, rural land or a former council area. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot. The table lists each plan with its one storey figures.
| Plan | Where it applies | Front | Side | Rear | Second street |
|---|---|---|---|---|---|
| Clarence Valley Residential Zones DCP 2011, Part Q Angourie village | Q1: "all land in the village of Angourie zoned R2 Low Density and R3 Medium Density residential zones in the CV LEP 2011". | 6m | inside a plane rising at 45° from 1.8m above the boundary, and at least 0.9m | inside a plane rising at 45° from 1.8m above the boundary, and at least 0.9m | inside a plane rising at 45° from 1.8m above the boundary, and at least 3.5m |
| Clarence Valley Residential Zones DCP 2011, Part R Glenreagh village | R1: "land in the village of Glenreagh zoned R2 Low Density Residential in CV LEP 2011". | the average of the neighbouring homes | 0.9m | 0.9m | 3.5m |
| Clarence Valley Residential Zones DCP 2011, Part U Ulmarra village | U1: "land within the R2 Low Density Residential zone in CV LEP 2011 in Ulmarra Village". | the average of the neighbouring homes | 0.9m | 0.9m | 3.5m |
| Clarence Valley Residential Zones DCP 2011, Schedule C1 item 2 (Yamba Shores Estate canal lots) | Lots in Yamba Shores Estate that take frontage to The Peninsula, The Anchorage, The Mainbrace, Mariners Way or Binnacle Court and have rear boundaries to the waterway in Lots 2 to 64 DP 1141129 (Schedule C1 item 2), on R1, R2 or R3 land. | at least 6m, or the street's established building line where that is further back | 0.9m | 3.5m | 3.5m |
| Clarence Valley DCPs, Queens Lane Iluka (northern side) | Land on the northern side of Queens Lane, Iluka, which backs onto the lane, zoned R3 (Residential Zones DCP C16.8) or SP3 (E and other zones DCP C17.3, C17.5). | 6m | 0.9m | 3.6m | 3.5m |
| Clarence Valley Residential Zones DCP 2011, Part C (R5 Large Lot Residential) | Land zoned R5 Large Lot Residential under Clarence Valley LEP 2011 (C16.3), including Gulmarrad (Part S, which sets no lot setbacks of its own). | at least 10m, or the street's established building line where that is further back | 3m, plus 1m for every metre of wall above 3m | 3m, plus 1m for every metre of wall above 3m | 6m |
| Clarence Valley Rural Zones DCP 2011, Part C (RU1, RU2) | Land zoned RU1 Primary Production or RU2 Rural Landscape under Clarence Valley LEP 2011 (Rural Zones DCP A3, C5.1). | at least 10m, or the street's established building line where that is further back | 3m, plus 1m for every metre of wall above 3m | 3m, plus 1m for every metre of wall above 3m | 6m |
| Clarence Valley DCP Development in E and other zones 2011, Part C (SP3 Tourist) | Land zoned SP3 Tourist under Clarence Valley LEP 2011 (E and other zones DCP A3, C17.1), including Yamba Hill SP3 land (Part P), except the lots on the northern side of Queens Lane, Iluka. | 6m | 0.9m | 0.9m | 3.5m |
What are the complying development setbacks for a granny flat?
If you build a granny flat with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, the setbacks come from the state codes, not from the council's DCP, and they depend on the lot's area and width. The table shows the complying development (CDC) figures the Site Checker uses for three example lots: 450m² (15m wide, 30m deep), 600m² (15m wide, 40m deep) and 1,000m² (20m wide, 50m deep). Your own lot's figures are in its report, and Can I use complying development on my block? explains which lots qualify.
| Example lot | Front | Side | Rear | Corner block, second street |
|---|---|---|---|---|
| 450m² (15m wide, 30m deep) | 4.5m | 0.9m (1.5m at two storeys) | 3m | 2m |
| 600m² (15m wide, 40m deep) | 4.5m | 0.9m (1.5m at two storeys) | 3m | 2m |
| 1,000m² (20m wide, 50m deep) | 6.5m | 1.5m | 5m | 3m |
What if my block is on a corner?
Clarence Valley Residential Zones DCP 2011, Part C (R1, R2, R3) sets a separate setback for a granny flat from the second street, the side street of a corner block: 3.5m (Residential Zones DCP 2011, Part C, C16.5). The complying development figure for the second street is in the CDC table above.
Does a two storey granny flat need bigger setbacks?
Yes, under Clarence Valley Residential Zones DCP 2011, Part C (R1, R2, R3): the side setback goes from 0.9m to 1.5m; the rear setback goes from 0.9m to 1.5m. Under complying development, the two storey figures are in the CDC table above.
What else do people ask?
Can Clarence Valley Council approve a granny flat closer to the boundary?
It can. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more. A complying development certificate has no such room: the design meets the code's setbacks or it is not complying development.
Do these setbacks apply to a shed, pool or fence in Clarence Valley?
No. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.
When were the setbacks on this page checked?
We last read Clarence Valley Council's plans on 12 November 2026. Each figure names the clause it came from, and each plan links to the council's own document, so you can check it against the current version.
Where does this information come from?
These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.