Skip to main content

How close to the boundary can a granny flat be in Albury City?

Albury City Council's main plan, Albury DCP 2010, Part 10, Divisions D and E (Zones R1, R3, E1 and MU1), asks a single storey granny flat for these setbacks: front the average of the neighbouring homes (4m where there are none), side 0.9m and rear 2m.

In Albury City the setbacks for a granny flat come from Albury City Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page is a first look: enter your address and the Site Checker opens at the setbacks for your lot, with the granny flat first.

Check your address

NSW addresses only. Free, and no sign up.

What setbacks does Albury City Council's main plan set for a granny flat?

The table gives Albury DCP 2010, Part 10, Divisions D and E (Zones R1, R3, E1 and MU1)'s one and two storey figures and the clause each comes from. The plan covers this land: Land in Zones R1 General Residential, R3 Medium Density Residential, E1 Local Centre and MU1 Mixed Use (formerly B1, B2 and B4): the main suburbs of Albury, Lavington, Thurgoona and Hamilton Valley.

Albury DCP 2010, Part 10, Divisions D and E (Zones R1, R3, E1 and MU1): setbacks for a granny flat
SetbackOne storeyTwo storeysWhere in the plan
Frontthe average of the neighbouring homes (4m where there are none)the average of the neighbouring homes (4m where there are none)Albury DCP 2010, Part 10, Division D, cl 2, Development Guidelines Table, c. ii Min. primary street setback for a secondary dwelling; c. i
Side0.9m1.5mAlbury DCP 2010, Part 10, Division D, cl 2, Development Guidelines Table, c. v Min. side setback
Rear2m6mAlbury DCP 2010, Part 10, Division D, cl 2, Development Guidelines Table, c. vi Min. rear setback
Corner block, second streetthe average of the neighbouring homes (2m where there are none)the average of the neighbouring homes (2m where there are none)Albury DCP 2010, Part 10, Division D, cl 2, Development Guidelines Table, c. iii Min. secondary street setback on a corner lot

Which DCP applies to my block in Albury City?

It depends on where the lot is. Albury DCP 2010, Part 10, Divisions D and E (Zones R1, R3, E1 and MU1) is Albury City Council's main plan, and 11 other plans cover a granny flat on particular land, such as a precinct, an estate, rural land or a former council area. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot. The table lists each plan with its one storey figures.

Other plans in Albury City that cover a granny flat
PlanWhere it appliesFrontSideRearSecond street
Albury DCP 2010, Part 10, Division C (Zone R2 Low Density Residential)Land in Zone R2 Low Density Residential (Albury's R2 is semi-rural: Splitters Creek fringe, Thurgoona and Ettamogah Rise).the average of the neighbouring homes (10m where there are none)2.5m10mthe average of the neighbouring homes (5m where there are none)
Albury DCP 2010, Part 10, Division C (Zone R5 Large Lot Residential)Land in Zone R5 Large Lot Residential outside Hamilton Valley.the average of the neighbouring homes (10m where there are none)5m10mthe average of the neighbouring homes (5m where there are none)
Albury DCP 2010, Part 9, Development in the Rural Zones (Zones RU1, RU4 and RU5)Land in Zones RU1 Primary Production, RU4 Primary Production Small Lots and RU5 Village (Table Top and Lake Hume villages).20m10m10m20m
Albury DCP 2010, Part 9, Development in the Rural Zones (Zone RU2 Rural Landscape)Land in Zone RU2 Rural Landscape, except the South Albury floodplain land in Figure 9.3 where the DCP does not permit dwellings.75m50m10m20m
Albury DCP 2010, Appendix F Hamilton Valley Design Guidelines (Standard Lots, Zone R1)R1 land in the suburb of Hamilton Valley (Figure 1.1 Lot Distribution and Framework Plan): the Standard Lots, and R1 lots over 1,150 m2, which Table 1.1 makes Rural Edge Lots (area tiers).4m on lots up to 1,150m²; 6m on lots up to 4,000m²; 10m on larger lots2.5m on lots up to 1,150m²; 5m on lots up to 4,000m²; 20m on larger lots2m2m on lots up to 1,150m²; 3m on lots up to 4,000m²; 5m on larger lots
Albury DCP 2010, Appendix F Hamilton Valley Design Guidelines (Rural Edge Lots, Zone R5)R5 land in the suburb of Hamilton Valley (Figure 1.1): the Rural Edge Lots with 4,000 m2 and 10,000 m2 minimums.6m on lots up to 4,000m²; 10m on larger lots5m on lots up to 4,000m²; 20m on larger lots10m3m on lots up to 4,000m²; 5m on larger lots
Albury DCP 2010, Appendix F Hamilton Valley Design Guidelines (Town Lots, Zone E1)The Hamilton Valley neighbourhood centre: E1 Local Centre land in the suburb of Hamilton Valley (three lots, 5.5 ha, at the Hamilton Valley Road roundabout).0m0m2m0m
Albury DCP 2010, Appendix F Hamilton Valley Design Guidelines (Village Lots)Village Lots in Hamilton Valley: medium density townhouse lots "Sited only directly adjoining a neighbourhood focal point" (Figure 1.1), usually 200 to 350 m2 with a rear service lane.2m0m to one side, 0.9m to the other2m2m
Show 3 more plans
Other plans in Albury City that cover a granny flat, continued
PlanWhere it appliesFrontSideRearSecond street
Albury DCP 2010, Appendix N Charles Sturt University: Albury CBD Development Control Plan 2010The former Charles Sturt University Albury CBD campus between Guinea, Olive, Wilson and David Streets (R1), less Adamshurst and the corner lots the plan leaves out.at least 4m, or the street's established building line where that is further back0.9m0.9mat least 2m, or the street's established building line where that is further back
Albury DCP 2010, Appendix N Charles Sturt University: Albury CBD Development Control Plan 2010 (Urban Residential precinct)The Urban Residential precinct of the former CSU Albury CBD campus (Figure A1.3 Precinct Character: the crescent of attached town houses around Adamshurst).0m0.9m0.9m0m
Albury DCP 2010, Part 10, Division I, Racecourse Estate Development Plan (Figure 2. a. i)Racecourse Estate, Lavington: the horse estate between Union Road, the Hume Freeway, Dallinger Road and the Albury Racecourse (Figure 2.7m3m3m7m

What are the complying development setbacks for a granny flat?

If you build a granny flat with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, the setbacks come from the state codes, not from the council's DCP, and they depend on the lot's area and width. The table shows the complying development (CDC) figures the Site Checker uses for three example lots: 450m² (15m wide, 30m deep), 600m² (15m wide, 40m deep) and 1,000m² (20m wide, 50m deep). Your own lot's figures are in its report, and Can I use complying development on my block? explains which lots qualify.

Complying development (CDC) setbacks for a granny flat on three example lots
Example lotFrontSideRearCorner block, second street
450m² (15m wide, 30m deep)4.5m0.9m (1.5m at two storeys)3m2m
600m² (15m wide, 40m deep)4.5m0.9m (1.5m at two storeys)3m2m
1,000m² (20m wide, 50m deep)6.5m1.5m5m3m

What if my block is on a corner?

Albury DCP 2010, Part 10, Divisions D and E (Zones R1, R3, E1 and MU1) sets a separate setback for a granny flat from the second street, the side street of a corner block: the average of the neighbouring homes (2m where there are none) (Albury DCP 2010, Part 10, Division D, cl 2, Development Guidelines Table, c. iii Min. secondary street setback on a corner lot). The complying development figure for the second street is in the CDC table above.

Does a two storey granny flat need bigger setbacks?

Yes, under Albury DCP 2010, Part 10, Divisions D and E (Zones R1, R3, E1 and MU1): the side setback goes from 0.9m to 1.5m; the rear setback goes from 2m to 6m. Under complying development, the two storey figures are in the CDC table above.

What else do people ask?

Can Albury City Council approve a granny flat closer to the boundary?

It can. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more. A complying development certificate has no such room: the design meets the code's setbacks or it is not complying development.

Do these setbacks apply to a shed, pool or fence in Albury City?

No. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.

When were the setbacks on this page checked?

We last read Albury City Council's plans on 12 November 2026. Each figure names the clause it came from, and each plan links to the council's own document, so you can check it against the current version.

Where does this information come from?

These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.

What else can I check?

Check what applies to your block