Skip to main content

How close to the boundary can a granny flat be in Parkes?

Parkes Council's main plan, Parkes Shire DCP 2021, Parts C.2 and C.3 (urban dwellings and medium density), asks a single storey granny flat for these setbacks: front the average of the neighbouring homes (4.5m where there are none) on lots up to 599.99m², the average of the neighbouring homes (6m where there are none) on larger lots; side 0.9m; and rear 3m on lots up to 599.99m², 5m on larger lots.

In Parkes the setbacks for a granny flat come from Parkes Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page is a first look: enter your address and the Site Checker opens at the setbacks for your lot, with the granny flat first.

Check your address

NSW addresses only. Free, and no sign up.

What setbacks does Parkes Council's main plan set for a granny flat?

The table gives Parkes Shire DCP 2021, Parts C.2 and C.3 (urban dwellings and medium density)'s one and two storey figures and the clause each comes from. The plan covers this land: Land zoned R1 General Residential, RU5 Village and MU1 Mixed Use under Parkes LEP 2012.

Parkes Shire DCP 2021, Parts C.2 and C.3 (urban dwellings and medium density): setbacks for a granny flat
SetbackOne storeyTwo storeysWhere in the plan
Frontthe average of the neighbouring homes (4.5m where there are none) on lots up to 599.99m², the average of the neighbouring homes (6m where there are none) on larger lotsnot set by the DCP: ask the councilParkes DCP 2021, Part C.3.5 Setbacks Standard Lots, standard a. table
Side0.9m1.5mParkes DCP 2021, Part C.3.5 Setbacks Standard Lots, standard a. table
Rear3m on lots up to 599.99m², 5m on larger lots5m on lots up to 599.99m², 8m on larger lotsParkes DCP 2021, Part C.3.5 Setbacks Standard Lots, standard a. table
Corner block, second street3m3mParkes DCP 2021, Part C.3.5 Setbacks Corner Lots, standard a. table

Which DCP applies to my block in Parkes?

It depends on where the lot is. Parkes Shire DCP 2021, Parts C.2 and C.3 (urban dwellings and medium density) is Parkes Council's main plan, and one other plan covers a granny flat on particular land, such as a precinct, an estate, rural land or a former council area. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot. The table lists each plan with its one storey figures.

Other plans in Parkes that cover a granny flat
PlanWhere it appliesFrontSideRearSecond street
Parkes Shire DCP 2021, Part C.6 (rural dwellings, RU1)Land zoned RU1 Primary Production under Parkes LEP 2012 (Part C.6.1).20mnot set by the DCP: ask the councilnot set by the DCP: ask the council20m

What are the complying development setbacks for a granny flat?

If you build a granny flat with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, the setbacks come from the state codes, not from the council's DCP, and they depend on the lot's area and width. The table shows the complying development (CDC) figures the Site Checker uses for three example lots: 450m² (15m wide, 30m deep), 600m² (15m wide, 40m deep) and 1,000m² (20m wide, 50m deep). Your own lot's figures are in its report, and Can I use complying development on my block? explains which lots qualify.

Complying development (CDC) setbacks for a granny flat on three example lots
Example lotFrontSideRearCorner block, second street
450m² (15m wide, 30m deep)4.5m0.9m (1.5m at two storeys)3m2m
600m² (15m wide, 40m deep)4.5m0.9m (1.5m at two storeys)3m2m
1,000m² (20m wide, 50m deep)6.5m1.5m5m3m

What if my block is on a corner?

Parkes Shire DCP 2021, Parts C.2 and C.3 (urban dwellings and medium density) sets a separate setback for a granny flat from the second street, the side street of a corner block: 3m (Parkes DCP 2021, Part C.3.5 Setbacks Corner Lots, standard a. table). The complying development figure for the second street is in the CDC table above.

Does a two storey granny flat need bigger setbacks?

Yes, under Parkes Shire DCP 2021, Parts C.2 and C.3 (urban dwellings and medium density): the front setback goes from the average of the neighbouring homes (4.5m where there are none) on lots up to 599.99m², the average of the neighbouring homes (6m where there are none) on larger lots to not set by the DCP: ask the council; the side setback goes from 0.9m to 1.5m; the rear setback goes from 3m on lots up to 599.99m², 5m on larger lots to 5m on lots up to 599.99m², 8m on larger lots. Under complying development, the two storey figures are in the CDC table above.

What else do people ask?

Can Parkes Council approve a granny flat closer to the boundary?

It can. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more. A complying development certificate has no such room: the design meets the code's setbacks or it is not complying development.

Do these setbacks apply to a shed, pool or fence in Parkes?

No. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.

When were the setbacks on this page checked?

We last read Parkes Council's plans on 12 November 2026. Each figure names the clause it came from, and each plan links to the council's own document, so you can check it against the current version.

Where does this information come from?

These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.

What else can I check?

Check what applies to your block