What are Tamworth Regional Council's setbacks for a house, granny flat or duplex?
A setback is how far a home must sit from each boundary of its lot. In Tamworth Regional the setbacks for a house, a granny flat or a duplex come from Tamworth Regional Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page reads what we hold for each of the three.
It is a first look. Enter your address and the Site Checker opens at the setbacks for your lot, from the plan that covers it.
NSW addresses only. Free, and no sign up.
What are Tamworth Regional Council's setbacks for a house?
Tamworth Regional Council's main plan, Tamworth Regional DCP 2010, Step 2 (Zone R1), asks a single storey house for these setbacks: front 4.5m, side left to the Building Code (0.9m) and rear left to the Building Code (0.9m).
House setbacks in Tamworth Regional gives the two storey figures, the clauses and every other plan that covers one.
What are Tamworth Regional Council's setbacks for a granny flat?
Tamworth Regional Council's main plan, Tamworth Regional DCP 2010, Step 2 (Zone R1), has no setback controls for a granny flat. Ask the council which controls it applies.
Granny flat setbacks in Tamworth Regional gives the complying development figures and every other plan that covers one.
What are Tamworth Regional Council's setbacks for a duplex?
Tamworth Regional Council's main plan, Tamworth Regional DCP 2010, Step 2 (Zone R1), asks a single storey duplex for these setbacks: front 4.5m, side 1m and rear 1m.
Duplex setbacks in Tamworth Regional gives the two storey figures, the clauses and every other plan that covers one.
Which DCP covers my block in Tamworth Regional?
It depends on the lot: we hold 14 plans with setbacks for homes in Tamworth Regional Council, and Tamworth Regional DCP 2010, Step 2 (Zone R1) is the main one. The others cover particular land, such as precincts, estates, rural land or former council areas. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot.
| Plan | Where it applies | Homes it covers |
|---|---|---|
| Tamworth Regional DCP 2010, Step 2 (Zone R1) | Main plan. Zone R1 General Residential land (Tamworth, Calala, Kootingal, Moore Creek and the other urban R1 areas), outside the Arcadia and Stratheden estates and the East and West Tamworth heritage conservation areas. | house, duplex |
| Tamworth Regional DCP 2010, Step 4 Heritage Conservation Areas with Step 2 (Zone R1, East and West Tamworth) | R1 land in the East Tamworth and West Tamworth Heritage Conservation Areas (Tamworth Regional LEP 2010, Amendment No 27). | house, duplex |
| Tamworth Regional DCP 2010, Step 4 Arcadia Estate (Zone R1) | R1 land in the Arcadia Estate (Werris Creek Road, Burgmanns Lane and Rodeo Drive, north of Tamworth; 286 ha in Figure 1). | house, duplex |
| Tamworth Regional DCP 2010, Step 4 Stratheden Estate (Zone R1) | R1 land in the Stratheden Estate (Browns Lane and Manilla Road), the "Area 1" land that LEP cl 7.13 requires a DCP for. The estate's R2 land (Lot Size Map W) takes the R2 V/W plan: the estate part sets no figures for it. | house, duplex |
| Tamworth Regional DCP 2010, Step 2 (Zone R2, Lot Size Map U) | R2 land on Lot Size Map U (1,000 m2), Hills Plain north of Tamworth (98 ha), except the lots adjoining R2 Lot Size Map V land. | house |
| Tamworth Regional DCP 2010, Step 2 (Zone R2, Lot Size Map U lots adjoining Lot Size Map V) | The 49 R2 Lot Size Map U lots in Hills Plain whose boundary adjoins an R2 Lot Size Map V lot. | house |
| Tamworth Regional DCP 2010, Step 2 (Zone R2, Lot Size Map V or W) | R2 land on Lot Size Map V (2,000 m2) or W (4,000 m2): Hills Plain, Moore Creek, Kootingal, Nemingha and other low density areas, and the R2 part of Stratheden (895 ha). | house |
| Tamworth Regional DCP 2010, Step 2 (Zone R2, Lot Size Map AA1) | R2 land on Lot Size Map AA1 (5 ha), 71 ha east of Hills Plain. | house |
Show 6 more plans
| Plan | Where it applies | Homes it covers |
|---|---|---|
| Tamworth Regional DCP 2010, Step 2 (Zone R5, Lot Size Map W) | R5 land on Lot Size Map W (4,000 m2), 290 ha. | house |
| Tamworth Regional DCP 2010, Step 2 (Zone R5, Lot Size Map Z or Y1) | R5 land on Lot Size Map Z (2 ha) or Y1 (1 ha), 9,264 ha: the large lot residential land around Tamworth, Kootingal, Moonbi and the villages. | house |
| Tamworth Regional DCP 2010, Step 2 (Zones RU1 and RU4) | Zone RU1 Primary Production and Zone RU4 Primary Production Small Lots land: the rural land of the region, including the former Manilla, Nundle, Barraba and Parry areas. | house, duplex |
| Tamworth Regional DCP 2010, Step 2 (Zone RU5) | Zone RU5 Village land: Manilla, Barraba, Nundle, Bendemeer, Attunga, Duri, Somerton, Woolomin, Dungowan and the other villages. | house, duplex |
| Tamworth Regional DCP 2010, Step 2 (Zone RU6) | Zone RU6 Transition land (216 ha, the landfill buffer west of Hills Plain). | house |
| Tamworth Regional DCP 2010, Step 2 (Zone C3) | Zone C3 Environmental Management land (7,566 ha). | house |
Do Tamworth Regional Council's setbacks apply to complying development?
No. A home approved with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, follows the state codes' setbacks instead of the council's. On a 600m² (15m wide, 40m deep) lot, for example, the Site Checker reads the complying development setbacks for a house as front 4.5m, side 0.9m (1.5m at two storeys) and rear 3m (8m at two storeys).
The council's plan applies when you lodge a development application. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.
What setbacks apply on a corner block in Tamworth Regional?
Tamworth Regional DCP 2010, Step 2 (Zone R1) sets a separate setback for a house from the second street, the side street of a corner block: 4.5m (Tamworth Regional DCP 2010, Step 2, General Housing and Ancillary Structures Development Controls, Building Setbacks table (p 9)). The front setback still applies to the main street. Under complying development the code sets its own second street figure by lot size.
What else do people ask?
Can Tamworth Regional Council approve a smaller setback?
It can, through a development application. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.
Do Tamworth Regional setbacks apply to sheds, pools and fences?
Not the ones on this page. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.
When were Tamworth Regional Council's setbacks checked?
We last read Tamworth Regional Council's plans on 12 November 2026. Each plan links to the council's own document, so you can check a figure against the current version.
Where does this information come from?
These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.