Skip to main content

How close to the boundary can a house be in Tamworth Regional?

Tamworth Regional Council's main plan, Tamworth Regional DCP 2010, Step 2 (Zone R1), asks a single storey house for these setbacks: front 4.5m, side left to the Building Code (0.9m) and rear left to the Building Code (0.9m).

In Tamworth Regional the setbacks for a house come from Tamworth Regional Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page is a first look: enter your address and the Site Checker opens at the setbacks for your lot, with the house first.

Check your address

NSW addresses only. Free, and no sign up.

What setbacks does Tamworth Regional Council's main plan set for a house?

The table gives Tamworth Regional DCP 2010, Step 2 (Zone R1)'s one and two storey figures and the clause each comes from. The plan covers this land: Zone R1 General Residential land (Tamworth, Calala, Kootingal, Moore Creek and the other urban R1 areas), outside the Arcadia and Stratheden estates and the East and West Tamworth heritage conservation areas.

Tamworth Regional DCP 2010, Step 2 (Zone R1): setbacks for a house
SetbackOne storeyTwo storeysWhere in the plan
Front4.5m4.5mTamworth Regional DCP 2010, Step 2, General Housing and Ancillary Structures Development Controls, Building Setbacks table (p 9)
Sideleft to the Building Code (0.9m)left to the Building Code (0.9m)Tamworth Regional DCP 2010, Step 2, General Housing and Ancillary Structures Development Controls, Building Setbacks table (p 9)
Rearleft to the Building Code (0.9m)left to the Building Code (0.9m)Tamworth Regional DCP 2010, Step 2, General Housing and Ancillary Structures Development Controls, Building Setbacks table (p 9)
Corner block, second street4.5m4.5mTamworth Regional DCP 2010, Step 2, General Housing and Ancillary Structures Development Controls, Building Setbacks table (p 9)

Which DCP applies to my block in Tamworth Regional?

It depends on where the lot is. Tamworth Regional DCP 2010, Step 2 (Zone R1) is Tamworth Regional Council's main plan, and 13 other plans cover a house on particular land, such as a precinct, an estate, rural land or a former council area. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot. The table lists each plan with its one storey figures.

Other plans in Tamworth Regional that cover a house
PlanWhere it appliesFrontSideRearSecond street
Tamworth Regional DCP 2010, Step 4 Heritage Conservation Areas with Step 2 (Zone R1, East and West Tamworth)R1 land in the East Tamworth and West Tamworth Heritage Conservation Areas (Tamworth Regional LEP 2010, Amendment No 27).the average of the neighbouring homesleft to the Building Code (0.9m)left to the Building Code (0.9m)4.5m
Tamworth Regional DCP 2010, Step 4 Arcadia Estate (Zone R1)R1 land in the Arcadia Estate (Werris Creek Road, Burgmanns Lane and Rodeo Drive, north of Tamworth; 286 ha in Figure 1).4.5mleft to the Building Code (0.9m)6m on lots up to 449.99m², left to the Building Code (0.9m) on larger lots2m on lots up to 449.99m², 4.5m on larger lots
Tamworth Regional DCP 2010, Step 4 Stratheden Estate (Zone R1)R1 land in the Stratheden Estate (Browns Lane and Manilla Road), the "Area 1" land that LEP cl 7.13 requires a DCP for. The estate's R2 land (Lot Size Map W) takes the R2 V/W plan: the estate part sets no figures for it.4.5mleft to the Building Code (0.9m)6m on lots up to 449.99m², left to the Building Code (0.9m) on larger lots2m on lots up to 449.99m², 4.5m on larger lots
Tamworth Regional DCP 2010, Step 2 (Zone R2, Lot Size Map U)R2 land on Lot Size Map U (1,000 m2), Hills Plain north of Tamworth (98 ha), except the lots adjoining R2 Lot Size Map V land.5.5m1m1m5.5m
Tamworth Regional DCP 2010, Step 2 (Zone R2, Lot Size Map U lots adjoining Lot Size Map V)The 49 R2 Lot Size Map U lots in Hills Plain whose boundary adjoins an R2 Lot Size Map V lot.7.5m1.5m1.5m7.5m
Tamworth Regional DCP 2010, Step 2 (Zone R2, Lot Size Map V or W)R2 land on Lot Size Map V (2,000 m2) or W (4,000 m2): Hills Plain, Moore Creek, Kootingal, Nemingha and other low density areas, and the R2 part of Stratheden (895 ha).10m2.5m2.5m10m
Tamworth Regional DCP 2010, Step 2 (Zone R2, Lot Size Map AA1)R2 land on Lot Size Map AA1 (5 ha), 71 ha east of Hills Plain.10m4m4m10m
Tamworth Regional DCP 2010, Step 2 (Zone R5, Lot Size Map W)R5 land on Lot Size Map W (4,000 m2), 290 ha.10m4m4m10m
Show 5 more plans
Other plans in Tamworth Regional that cover a house, continued
PlanWhere it appliesFrontSideRearSecond street
Tamworth Regional DCP 2010, Step 2 (Zone R5, Lot Size Map Z or Y1)R5 land on Lot Size Map Z (2 ha) or Y1 (1 ha), 9,264 ha: the large lot residential land around Tamworth, Kootingal, Moonbi and the villages.20m10m10m20m
Tamworth Regional DCP 2010, Step 2 (Zones RU1 and RU4)Zone RU1 Primary Production and Zone RU4 Primary Production Small Lots land: the rural land of the region, including the former Manilla, Nundle, Barraba and Parry areas.20m10m10m20m
Tamworth Regional DCP 2010, Step 2 (Zone RU5)Zone RU5 Village land: Manilla, Barraba, Nundle, Bendemeer, Attunga, Duri, Somerton, Woolomin, Dungowan and the other villages.6mleft to the Building Code (0.9m)left to the Building Code (0.9m)6m
Tamworth Regional DCP 2010, Step 2 (Zone RU6)Zone RU6 Transition land (216 ha, the landfill buffer west of Hills Plain).10m4m4m10m
Tamworth Regional DCP 2010, Step 2 (Zone C3)Zone C3 Environmental Management land (7,566 ha).20m10m10m20m

What are the complying development setbacks for a house?

If you build a house with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, the setbacks come from the state codes, not from the council's DCP, and they depend on the lot's area and width. The table shows the complying development (CDC) figures the Site Checker uses for three example lots: 450m² (15m wide, 30m deep), 600m² (15m wide, 40m deep) and 1,000m² (20m wide, 50m deep). Your own lot's figures are in its report, and Can I use complying development on my block? explains which lots qualify.

Complying development (CDC) setbacks for a house on three example lots
Example lotFrontSideRearCorner block, second street
450m² (15m wide, 30m deep)4.5m0.9m (1.5m at two storeys)3m (8m at two storeys)2m
600m² (15m wide, 40m deep)4.5m0.9m (1.5m at two storeys)3m (8m at two storeys)2m
1,000m² (20m wide, 50m deep)6.5m1.5m (2.1m at two storeys)5m (12m at two storeys)3m

What if my block is on a corner?

Tamworth Regional DCP 2010, Step 2 (Zone R1) sets a separate setback for a house from the second street, the side street of a corner block: 4.5m (Tamworth Regional DCP 2010, Step 2, General Housing and Ancillary Structures Development Controls, Building Setbacks table (p 9)). The complying development figure for the second street is in the CDC table above.

Does a two storey house need bigger setbacks?

No. Tamworth Regional DCP 2010, Step 2 (Zone R1) sets the same figures for a one or two storey house. Under complying development, the two storey figures are in the CDC table above.

What else do people ask?

Can Tamworth Regional Council approve a house closer to the boundary?

It can. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more. A complying development certificate has no such room: the design meets the code's setbacks or it is not complying development.

Do these setbacks apply to a shed, pool or fence in Tamworth Regional?

No. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.

When were the setbacks on this page checked?

We last read Tamworth Regional Council's plans on 12 November 2026. Each figure names the clause it came from, and each plan links to the council's own document, so you can check it against the current version.

Where does this information come from?

These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.

What else can I check?

Check what applies to your block