Skip to main content

What are Bellingen Council's setbacks for a house, granny flat or duplex?

A setback is how far a home must sit from each boundary of its lot. In Bellingen the setbacks for a house, a granny flat or a duplex come from Bellingen Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page reads what we hold for each of the three.

It is a first look. Enter your address and the Site Checker opens at the setbacks for your lot, from the plan that covers it.

Check your address

NSW addresses only. Free, and no sign up.

What are Bellingen Council's setbacks for a house?

Bellingen Council's main plan, Bellingen Shire DCP 2017, Chapters 1 and 2 (R1 General Residential), asks a single storey house for these setbacks: front at least 4.5m, or the street's established building line where that is further back; side inside a plane rising at 35° from 3m above the boundary, and at least 0.9m; and rear inside a plane rising at 35° from 3m above the boundary.

House setbacks in Bellingen gives the two storey figures, the clauses and every other plan that covers one.

What are Bellingen Council's setbacks for a granny flat?

Bellingen Council's main plan, Bellingen Shire DCP 2017, Chapters 1 and 2 (R1 General Residential), asks a single storey granny flat for these setbacks: front at least 4.5m, or the street's established building line where that is further back; side inside a plane rising at 35° from 3m above the boundary, and at least 0.9m; and rear inside a plane rising at 35° from 3m above the boundary.

Granny flat setbacks in Bellingen gives the two storey figures, the clauses and every other plan that covers one.

What are Bellingen Council's setbacks for a duplex?

Bellingen Council's main plan, Bellingen Shire DCP 2017, Chapters 1 and 2 (R1 General Residential), asks a single storey duplex for these setbacks: front at least 4.5m, or the street's established building line where that is further back; side inside a plane rising at 35° from 3m above the boundary, and at least 0.9m; and rear inside a plane rising at 35° from 3m above the boundary.

Duplex setbacks in Bellingen gives the two storey figures, the clauses and every other plan that covers one.

Which DCP covers my block in Bellingen?

It depends on the lot: we hold 4 plans with setbacks for homes in Bellingen Council, and Bellingen Shire DCP 2017, Chapters 1 and 2 (R1 General Residential) is the main one. The others cover particular land, such as precincts, estates, rural land or former council areas. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot.

Every plan in Bellingen with setbacks for homes
PlanWhere it appliesHomes it covers
Bellingen Shire DCP 2017, Chapters 1 and 2 (R1 General Residential)Main plan. R1 General Residential land in Bellingen Shire (the towns and villages, including Bellingen, North Bellingen and its Chapter 17 urban release area, Urunga, Dorrigo and Mylestom).house, granny flat, duplex
Bellingen Shire DCP 2017, Chapters 1 and 2 (R5 Large Lot Residential)R5 Large Lot Residential land in Bellingen Shire.house, granny flat, duplex
Bellingen Shire DCP 2017, Chapters 1 and 2 (RU1, RU2 and RU4 rural zones)RU1 Primary Production, RU2 Rural Landscape and RU4 Primary Production Small Lots land in Bellingen Shire.house, granny flat, duplex
Bellingen Shire DCP 2017, Chapter 1 (C3 Environmental Management and C4 Environmental Living)C3 Environmental Management and C4 Environmental Living land in Bellingen Shire, the zones Table 1.1 calls "E3, E4" (renamed C3 and C4 by the Standard Instrument (Local Environmental Plans) Amendment (Land Use Zones) Order 2021, which the council's DCP page links).house

Do Bellingen Council's setbacks apply to complying development?

No. A home approved with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, follows the state codes' setbacks instead of the council's. On a 600m² (15m wide, 40m deep) lot, for example, the Site Checker reads the complying development setbacks for a house as front 4.5m, side 0.9m (1.5m at two storeys) and rear 3m (8m at two storeys).

The council's plan applies when you lodge a development application. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.

What setbacks apply on a corner block in Bellingen?

Bellingen Shire DCP 2017, Chapters 1 and 2 (R1 General Residential) sets a separate setback for a house from the second street, the side street of a corner block: inside a plane rising at 35° from 3m above the boundary, and at least 3m (Bellingen Shire DCP 2017, Chapter 1 Single Dwellings, 1.6.1 Setbacks from boundaries, criterion 1, Table 1.1; Bellingen Shire DCP 2017, Chapter 1 Single Dwellings, 1.6.3 The Building Height Plane Envelope, criterion 1 and Figure 1.1). The front setback still applies to the main street. Under complying development the code sets its own second street figure by lot size.

What else do people ask?

Can Bellingen Council approve a smaller setback?

It can, through a development application. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.

Do Bellingen setbacks apply to sheds, pools and fences?

Not the ones on this page. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.

When were Bellingen Council's setbacks checked?

We last read Bellingen Council's plans on 12 November 2026. Each plan links to the council's own document, so you can check a figure against the current version.

Where does this information come from?

These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.

What else can I check?

Check what applies to your block