Skip to main content

What are Warren Council's setbacks for a house, granny flat or duplex?

A setback is how far a home must sit from each boundary of its lot. In Warren the setbacks for a house, a granny flat or a duplex come from Warren Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page reads what we hold for each of the three.

It is a first look. Enter your address and the Site Checker opens at the setbacks for your lot, from the plan that covers it.

Check your address

NSW addresses only. Free, and no sign up.

What are Warren Council's setbacks for a house?

Warren Council's main plan, Warren Shire Council DCP 2013: R1 General Residential (no setback controls), names a house but sets no front, side or rear setback for one, so a development application is assessed on its merits. Ask the council what it expects.

House setbacks in Warren gives the complying development figures and every other plan that covers one.

What are Warren Council's setbacks for a granny flat?

Warren Council's main plan, Warren Shire Council DCP 2013: R1 General Residential (no setback controls), names a granny flat but sets no front, side or rear setback for one, so a development application is assessed on its merits. Ask the council what it expects.

Granny flat setbacks in Warren gives the complying development figures and every other plan that covers one.

What are Warren Council's setbacks for a duplex?

Warren Council's main plan, Warren Shire Council DCP 2013: R1 General Residential (no setback controls), names a duplex but sets no front, side or rear setback for one, so a development application is assessed on its merits. Ask the council what it expects.

Duplex setbacks in Warren gives the complying development figures and every other plan that covers one.

Which DCP covers my block in Warren?

It depends on the lot: we hold 5 plans with setbacks for homes in Warren Council, and Warren Shire Council DCP 2013: R1 General Residential (no setback controls) is the main one. The others cover particular land, such as precincts, estates, rural land or former council areas. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot.

Every plan in Warren with setbacks for homes
PlanWhere it appliesHomes it covers
Warren Shire Council DCP 2013: R1 General Residential (no setback controls)Main plan. Land zoned R1 General Residential (the town of Warren).house, granny flat, duplex
Warren Shire Council DCP 2013: RU5 Village (no setback controls)Land zoned RU5 Village (Nevertire and Collie).house, granny flat, duplex
Warren Shire Council DCP 2013, Dwelling Houses in Zone R5 Large Lot Residential (cl 15 to 19)Land zoned R5 Large Lot Residential.house, granny flat, duplex
Warren Shire Council DCP 2013: RU1 Primary Production and RU6 Transition (no setback controls)Land zoned RU1 Primary Production or RU6 Transition.house, granny flat
Warren Shire Council DCP 2013: E3 Productivity Support (no setback controls)Land zoned E3 Productivity Support, where the LEP permits a dwelling house but not a granny flat or duplex.house

Do Warren Council's setbacks apply to complying development?

No. A home approved with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, follows the state codes' setbacks instead of the council's. On a 600m² (15m wide, 40m deep) lot, for example, the Site Checker reads the complying development setbacks for a house as front 4.5m, side 0.9m (1.5m at two storeys) and rear 3m (8m at two storeys).

The council's plan applies when you lodge a development application. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.

What setbacks apply on a corner block in Warren?

Warren Shire Council DCP 2013: R1 General Residential (no setback controls) sets no separate setback for the second street of a corner block for a house, so ask the council how it treats one. Under complying development the code sets one by lot size.

What else do people ask?

Can Warren Council approve a smaller setback?

It can, through a development application. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.

Do Warren setbacks apply to sheds, pools and fences?

Not the ones on this page. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.

When were Warren Council's setbacks checked?

We last read Warren Council's plans on 12 November 2026. Each plan links to the council's own document, so you can check a figure against the current version.

Where does this information come from?

These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.

What else can I check?

Check what applies to your block