What are Bourke Council's setbacks for a house, granny flat or duplex?
A setback is how far a home must sit from each boundary of its lot. In Bourke the setbacks for a house, a granny flat or a duplex come from Bourke Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page reads what we hold for each of the three.
It is a first look. Enter your address and the Site Checker opens at the setbacks for your lot, from the plan that covers it.
NSW addresses only. Free, and no sign up.
What are Bourke Council's setbacks for a house?
Bourke Council's main plan, Bourke Shire DCP 2012, s 4.3 and 4.4 (R1 General Residential), asks a single storey house for these setbacks: front 4.5m, side left to the Building Code (0.9m) and rear left to the Building Code (0.9m).
House setbacks in Bourke gives the two storey figures, the clauses and every other plan that covers one.
What are Bourke Council's setbacks for a granny flat?
Bourke Council's main plan, Bourke Shire DCP 2012, s 4.3 and 4.4 (R1 General Residential), asks a single storey granny flat for these setbacks: front 4.5m, side left to the Building Code (0.9m) and rear left to the Building Code (0.9m).
Granny flat setbacks in Bourke gives the two storey figures, the clauses and every other plan that covers one.
What are Bourke Council's setbacks for a duplex?
Bourke Council's main plan, Bourke Shire DCP 2012, s 4.3 and 4.4 (R1 General Residential), asks a single storey duplex for these setbacks: front 4.5m, side 1m and rear 1m.
Duplex setbacks in Bourke gives the two storey figures, the clauses and every other plan that covers one.
Which DCP covers my block in Bourke?
It depends on the lot: we hold 5 plans with setbacks for homes in Bourke Council, and Bourke Shire DCP 2012, s 4.3 and 4.4 (R1 General Residential) is the main one. The others cover particular land, such as precincts, estates, rural land or former council areas. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot.
| Plan | Where it applies | Homes it covers |
|---|---|---|
| Bourke Shire DCP 2012, s 4.3 and 4.4 (R1 General Residential) | Main plan. Land zoned R1 General Residential (Bourke town: 266.6 ha, and an 18.4 ha R1 area west of the town; 285 ha in all). | house, granny flat, duplex |
| Bourke Shire DCP 2012, s 4.3 and 4.4 (RU5 Village) | Land zoned RU5 Village (eight areas, 107.5 ha: the villages of Byrock, Enngonia, Louth and Wanaaring, Fords Bridge, and a 33.6 ha RU5 area at North Bourke). | house, granny flat, duplex |
| Bourke Shire DCP 2012, s 4.3 and 4.4 (R5 Large Lot Residential) | All R5 Large Lot Residential land (403.7 ha: North Bourke, north east of North Bourke and the east edge of Bourke), whatever its Lot Size Map minimum (1, 2 or 10 ha). | house, granny flat, duplex |
| Bourke Shire DCP 2012, s 4.3 and 4.4 (RU1 Primary Production) | Land zoned RU1 Primary Production (almost all of the shire). | house, duplex |
| Bourke Shire DCP 2012 (E1 Local Centre, no setback figures for houses, granny flats or duplexes) | Land zoned E1 Local Centre (Bourke town centre, 19.3 ha). | house, granny flat, duplex |
Do Bourke Council's setbacks apply to complying development?
No. A home approved with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, follows the state codes' setbacks instead of the council's. On a 600m² (15m wide, 40m deep) lot, for example, the Site Checker reads the complying development setbacks for a house as front 4.5m, side 0.9m (1.5m at two storeys) and rear 3m (8m at two storeys).
The council's plan applies when you lodge a development application. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.
What setbacks apply on a corner block in Bourke?
Bourke Shire DCP 2012, s 4.3 and 4.4 (R1 General Residential) sets a separate setback for a house from the second street, the side street of a corner block: 4.5m (Bourke Shire DCP 2012, s 4.3.1 Building Setbacks, table; s 4.6.1 Lot size). The front setback still applies to the main street. Under complying development the code sets its own second street figure by lot size.
What else do people ask?
Can Bourke Council approve a smaller setback?
It can, through a development application. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more.
Do Bourke setbacks apply to sheds, pools and fences?
Not the ones on this page. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.
When were Bourke Council's setbacks checked?
We last read Bourke Council's plans on 12 November 2026. Each plan links to the council's own document, so you can check a figure against the current version.
Where does this information come from?
These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.