How close to the boundary can a house be in Ballina?
Ballina Council's main plan, Ballina Shire DCP 2012, Chapter 4 (Zones R2 and R3, no building line mapped), asks a single storey house for these setbacks: front at least 4.5m, or the street's established building line where that is further back; side 0.9m to one side, 0.9m to the other; and rear 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)).
In Ballina the setbacks for a house come from Ballina Council's development control plan (DCP), the council's own rules for the design of homes in its area, unless you build as complying development, which follows state rules instead. This page is a first look: enter your address and the Site Checker opens at the setbacks for your lot, with the house first.
NSW addresses only. Free, and no sign up.
What setbacks does Ballina Council's main plan set for a house?
The table gives Ballina Shire DCP 2012, Chapter 4 (Zones R2 and R3, no building line mapped)'s one and two storey figures and the clause each comes from. The plan covers this land: Land in Zone R2 Low Density Residential or Zone R3 Medium Density Residential that the Building Line Map does not cover.
| Setback | One storey | Two storeys | Where in the plan |
|---|---|---|---|
| Front | at least 4.5m, or the street's established building line where that is further back | at least 4.5m, or the street's established building line where that is further back | Chapter 4, s 3.1.3.2 Setbacks (ii) |
| One side | 0.9m | 2.5m for walls more than 4.5 m above existing ground level (the ground floor may sit at 0.9 m) | Chapter 4, s 3.1.3.2 Setbacks (v) and (vi) |
| Other side | 0.9m | 1.5m for walls more than 4.5 m above existing ground level (the ground floor may sit at 0.9 m) | Chapter 4, s 3.1.3.2 Setbacks (v) and (vi) |
| Rear | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | Chapter 4, s 3.1.3.2 Setbacks (viii) |
| Corner block, second street | 3m | 3m | Chapter 4, s 3.1.3.2 Setbacks (iv) |
Which DCP applies to my block in Ballina?
It depends on where the lot is. Ballina Shire DCP 2012, Chapter 4 (Zones R2 and R3, no building line mapped) is Ballina Council's main plan, and 38 other plans cover a house on particular land, such as a precinct, an estate, rural land or a former council area. Many councils have several plans, set by zone, estate, precinct or former council area, so enter your address and the Site Checker picks the plan that covers your lot. The table lists each plan with its one storey figures.
| Plan | Where it applies | Front | Side | Rear | Second street |
|---|---|---|---|---|---|
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (3 m street building line) | Land in Zone R2 or R3 inside the 3 m street building line on the Building Line Map: Lennox Village Estate (Barrett Drive area, 3.0 m part) and the Walker Lane area (Cumbalum, 3.0 m from the Unara Parkway boundary). | 3m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (3.5 m street building line) | Land in Zone R2 or R3 inside the 3.5 m street building line on the Building Line Map: Warrawee Drive, Lennox Head. | 3.5m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (4 m street building line) | Land in Zone R2 or R3 inside the 4 m street building line on the Building Line Map: Ferngrove Estate (Ballina), Castle Drive and Lennox Village Estate (Lennox Head, 4.0 m parts) and Condon Drive (East Ballina). | 4m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (4.3 m street building line) | Land in Zone R2 or R3 inside the 4.3 m street building line on the Building Line Map: Castle Drive, Lennox Head (4.3 m part). | 4.3m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (4.6 m street building line) | Land in Zone R2 or R3 inside the 4.6 m street building line on the Building Line Map: the general 4.6 m building lines: Ballina, East Ballina (4.6 m part), Wardell, Alstonville village centre, Shelly Beach, Allens Parade/Dress Circle Drive (Lennox Head) and Kim Court. | 4.6m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (6 m street building line) | Land in Zone R2 or R3 inside the 6 m street building line on the Building Line Map: the general 6.0 m building lines: Lennox Head, East Ballina (6.0 m part), West Ballina, North Ballina, Skennars Head, Cumbalum, Wollongbar, Alstonville, and the Bayswater Gardens, Sandpiper Court, Namatjira Place, Banyanda, Grosvenor Gardens and Riveroaks (general) estates. | 6m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (7 m street building line) | Land in Zone R2 or R3 inside the 7 m street building line on the Building Line Map: Midhaven Estate (Acacia Avenue area). | 7m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (7.6 m street building line) | Land in Zone R2 or R3 inside the 7.6 m street building line on the Building Line Map: Shaws Bay area, East Ballina. | 7.6m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
Show 30 more plans
| Plan | Where it applies | Front | Side | Rear | Second street |
|---|---|---|---|---|---|
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Greenfield Road 20 m) | Land in Zone R2 or R3 in the Greenfield Road Area (Greenfield Estate, DP 258095), on the Building Line Map. | 20m (from the Greenfield Road frontage) | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Trilby Avenue, Burke Walk and Woods Walk) | Land in Zone R2 or R3 in the Trilby Avenue / Burke Walk / Woods Walk area, East Ballina: 3.0 m from the street or park, 1.0 m from the lane. | 3m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Headlands Drive 3.0 m) | Land in Zone R2 or R3 in the Headlands Drive setback area, Skennars Head. | 3m (from the Headlands Drive frontage) | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Warrawee Drive / Karalauren Court, North Creek Road) | Land in Zone R2 or R3 in the Warrawee Drive / Karalauren Court area, Lennox Head, which backs onto North Creek Road. | 6m | 0.9m to one side, 0.9m to the other | 4m (from the North Creek Road boundary, full width) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Ocean View Estate) | Land in Zone R2 or R3 in the Ocean View Estate (Ocean View Drive area), Alstonville. | 4.6m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (estates with building envelopes) | Land in Zone R2 or R3 in an estate whose building lines are set by its own consent, plan or 88B plan: North Lakes, Whiting Way, Edgewater Cove, Avalon, Wollongbar Park (Kurrabri), Aspects (DP 1121058), Cumbalum Park, Greenwood Grove and Rainforest Ridge. | not set by the DCP: ask the council | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Ballina Quays Estate foreshore building line) | Land in Zone R2 or R3 in Ballina Quays Estate, West Ballina. | 6m | 0.9m to one side, 0.9m to the other | 11.5m (from the canal boundary) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Banyanda Lake foreshore building line) | Land in Zone R2 or R3 around Banyanda Lake, West Ballina. | 6m | 0.9m to one side, 0.9m to the other | 8.2m (from the lake boundary) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Riverside Drive foreshore building line) | Land in Zone R2 or R3 on the river side of Riverside Drive, West Ballina. | 6m | 0.9m to one side, 0.9m to the other | 4.6m (from the southern (river side) boundary) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Anchorage Point and Waterview Court 3.0 m foreshore building line) | Land in Zone R2 or R3 at Anchorage Point and Waterview Court (DP 850782), West Ballina, that backs onto the Richmond River and carries the 3.0 m foreshore building line on the Building Line Map (inside the West Ballina 6.0 m street line): Lot 14 DP 1113273 at Anchorage Point and two Waterview Court lots (Lot 2 DP 1018472, SP 55312). | 6m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Anchorage Point and Waterview Court 4.0 m foreshore building line) | Land in Zone R2 or R3 at Anchorage Point and Waterview Court (DP 850782), West Ballina, that backs onto the Richmond River and carries the 4.0 m foreshore building line on the Building Line Map (inside the West Ballina 6.0 m street line): six Anchorage Point lots in DP 1113273 and six Waterview Court lots in DP 850782. | 6m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (North Creek foreshore building line) | Land in Zone R2 or R3 on North Creek between Cawarra Street and Crowley Village, Ballina, inside the 4.6 m street line. | 4.6m | 0.9m to one side, 0.9m to the other | 4.6m (from the North Creek boundary) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (North Creek foreshore building line) | Land in Zone R2 or R3 on North Creek in Sandpiper Court, Ballina, inside the 6.0 m street line. | 6m | 0.9m to one side, 0.9m to the other | 4.6m (from the North Creek boundary) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Douglas Street foreshore building line) | Land in Zone R2 or R3 on Douglas Street, East Ballina (27 m foreshore building line). | 4.6m | 0.9m to one side, 0.9m to the other | no building more than 27m from the front boundary (no building more than 27 m from the Douglas Street boundary) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Azure/Unnamed Lane, western side, 4.6 m lane line) | Land in Zone R2 or R3 on the western side of Azure/Unnamed Lane, East Ballina (4.6 m lane line, inside the East Ballina 4.6 m street line). | 4.6m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 with the Building Line Map (Holden Lane north side, Cherry Street to Kerr Street) | Land in Zone R2 or R3 on the north side of Holden Lane between Cherry Street and Kerr Street, Ballina (inside the Ballina 4.6 m street line). | 4.6m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4, Part 4.7 Blue Seas Parade Estate | Land in Zone R2 or R3 in the Blue Seas Parade Estate, Lennox Head (Special Area Controls Map, sheet SR_003_020). | at least 4.5m, or the street's established building line where that is further back | 0.9m to one side, 0.9m to the other | 5m (from the rear (eastern) boundary, and clear of any right of carriageway) | 3m |
| Ballina Shire DCP 2012, Chapter 4, Part 4.6 16 Tara Downs, Lennox Head | Land in Zone R2 or R3 at 16 Tara Downs, Lennox Head (Special Area Controls Map). | at least 4.5m, or the street's established building line where that is further back | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4, Part 4.8 23 Compton Drive, East Ballina | 23 Compton Drive, East Ballina (Lot 3 DP 525783), in Zone R2 or R3. | 0m | not set by the DCP: ask the council | not set by the DCP: ask the council | 3m |
| Ballina Shire DCP 2012, Chapter 4, Part 4.4 Camden Lane (foreshore building lines) | Land in Zone R2 or R3 in the Camden Lane area, Ballina, on North Creek: 1, 3 and 5 Camden Lane and 2 Skinner Street. | not set by the DCP: ask the council | 0.9m to one side, 0.9m to the other | not set by the DCP: ask the council | 3m |
| Ballina Shire DCP 2012, Chapter 4, Part 4.5 Lennox Head Coastal Hazard (foreshore building lines) | Land in Zone R2 or R3 in the Lennox Head Coastal Hazard Protection Area (Ballina Street, Rayner Lane, Rutherford Street and Allens Parade beachfront lots). | not set by the DCP: ask the council | 0.9m to one side, 0.9m to the other | not set by the DCP: ask the council | 3m |
| Ballina Shire DCP 2012, Chapter 4, Part 4.2 Aspects Estate & Elevation Estate, Lennox Head (mews allotments) | Land in Zone R2 or R3 in the Aspects and Elevation estates, Lennox Head (Special Area Controls Map), inside the Lennox Head 6.0 m street line. | 6m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 4 on Ballina LEP 1987 land (Zones 2 (a) and 2 (b), deferred matter) | Deferred matter land under Ballina LEP 2012 that Ballina LEP 1987 zones 2 (a) Living Area or 2 (b) Village Area: about 31 ha in 25 parcels, mainly Wardell (10 ha of 2 (b)) and Lennox Head and Skennars Head (2 (a)). | at least 4.5m, or the street's established building line where that is further back | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 7, s 4.2 Fig Tree Hill, Lennox Head (Chapter 4 controls) | Land on the Fig Tree Hill Neighbourhood Map (sheet FT_001_010), Lennox Head: Fig Tree Hill Drive and Hilltop Place, Zone RU1. | 6m | 0.9m to one side, 0.9m to the other | 4m (at least 30% of the lot width, verandahs, patios and decks included; the rest of the rear wall may sit at 0.9 m (2.5 m or 1.5 m for walls over 4.5 m)) | 3m |
| Ballina Shire DCP 2012, Chapter 7 Rural Living and Activity (Zones RU1 and RU2) | Land in Zone RU1 Primary Production or Zone RU2 Rural Landscape with no rural building line on the Building Line Map. Secondary dwellings are prohibited in both zones (Ballina LEP 2012; the Housing SEPP s 50 reaches only R zones). | 20m (from a sealed road) | 10m | not set by the DCP: ask the council | 10m |
| Ballina Shire DCP 2012, Chapter 7 Rural Living and Activity (Zones C2 and C3) | Land in Zone C2 Environmental Conservation or Zone C3 Environmental Management. | 20m (from a sealed road) | 10m | not set by the DCP: ask the council | 10m |
| Ballina Shire DCP 2012, Chapter 7 with the Building Line Map (6 m rural building line) | Land in Zone RU1 or RU2 inside a 6 m rural building line on the Building Line Map. | 6m | 10m | not set by the DCP: ask the council | 10m |
| Ballina Shire DCP 2012, Chapter 7 with the Building Line Map (10 m rural building line) | Land in Zone RU1 or RU2 inside a 10 m rural building line on the Building Line Map. | 10m | 10m | not set by the DCP: ask the council | 10m |
| Ballina Shire DCP 2012, Chapter 7 with the Building Line Map (25 m rural building line) | Land in Zone RU1 or RU2 inside a 25 m rural building line on the Building Line Map. | 25m (from the Platypus Drive (Forest Hills) or Fredericks Lane (Oatley Park) frontage) | 10m | not set by the DCP: ask the council | 10m |
| Ballina Shire DCP 2012, Chapter 7 with the Building Line Map (rural estates with building envelopes) | Land in Zone RU1 or RU2 in Victory Farm (Nelson Chase), Norfolk Park or Towalbyn estates, whose building lines are set by their consent or plan. | not set by the DCP: ask the council | 10m | not set by the DCP: ask the council | 10m |
What are the complying development setbacks for a house?
If you build a house with a complying development certificate (CDC), the fast approval a private certifier can issue when a design meets the state's fixed standards, the setbacks come from the state codes, not from the council's DCP, and they depend on the lot's area and width. The table shows the complying development (CDC) figures the Site Checker uses for three example lots: 450m² (15m wide, 30m deep), 600m² (15m wide, 40m deep) and 1,000m² (20m wide, 50m deep). Your own lot's figures are in its report, and Can I use complying development on my block? explains which lots qualify.
| Example lot | Front | Side | Rear | Corner block, second street |
|---|---|---|---|---|
| 450m² (15m wide, 30m deep) | 4.5m | 0.9m (1.5m at two storeys) | 3m (8m at two storeys) | 2m |
| 600m² (15m wide, 40m deep) | 4.5m | 0.9m (1.5m at two storeys) | 3m (8m at two storeys) | 2m |
| 1,000m² (20m wide, 50m deep) | 6.5m | 1.5m (2.1m at two storeys) | 5m (12m at two storeys) | 3m |
What if my block is on a corner?
Ballina Shire DCP 2012, Chapter 4 (Zones R2 and R3, no building line mapped) sets a separate setback for a house from the second street, the side street of a corner block: 3m (Chapter 4, s 3.1.3.2 Setbacks (iv)). The complying development figure for the second street is in the CDC table above.
Does a two storey house need bigger setbacks?
Yes, under Ballina Shire DCP 2012, Chapter 4 (Zones R2 and R3, no building line mapped): the one side setback goes from 0.9m to 2.5m for walls more than 4.5 m above existing ground level (the ground floor may sit at 0.9 m); the other side setback goes from 0.9m to 1.5m for walls more than 4.5 m above existing ground level (the ground floor may sit at 0.9 m). Under complying development, the two storey figures are in the CDC table above.
What else do people ask?
Can Ballina Council approve a house closer to the boundary?
It can. A development application (DA) is assessed on its merits, so the council can accept less than its plan asks for where a design justifies it, or ask for more. A complying development certificate has no such room: the design meets the code's setbacks or it is not complying development.
Do these setbacks apply to a shed, pool or fence in Ballina?
No. Sheds, pergolas, carports, pools, decks and fences follow different rules (exempt development, which needs no approval when it meets them), and these pages do not cover them.
When were the setbacks on this page checked?
We last read Ballina Council's plans on 12 November 2026. Each figure names the clause it came from, and each plan links to the council's own document, so you can check it against the current version.
Where does this information come from?
These pages are a first look at the setbacks in each council's published development control plan and in the complying development codes, read from the documents linked on each page. They are not a section 10.7 planning certificate or a design check, and a council plan can change after we read it. Confirm anything you rely on with the council or a certifier before you buy, design or build. Nothing on this page replaces advice from your certifier, engineer, lawyer or your own designer.